Advertisement
Quick Links
Advertisement
Related Manuals for logitrans WSP 2200
Summary of Contents for logitrans WSP 2200
- Page 1 User Guide Handpallet weighter WSP 2200...
- Page 3 Basic usage informations Correct usage Handpallet weighter KPZ should be used mainly for measurement reasons. As a non- automatic measurement device, is providing the values of weighted items. It can be used on the smooth and flat surface. The goods are weighted on the pallet. Centre of gravity should be placed in the middle.
- Page 4 Basic safety guidelines Following the guidelines Please read this user guide very carefully and follow the procedures saved in this document. Staff Handling and protection service should not be made by not properly prepared staff without authorization. Scale should be handled by trained staff. Basic safety guidelines - Make sure that device is in good technical condition.
- Page 5 Unpacking, shipment and storing Inspection during collection During scale collection, please check packaging and scale for any potential outside and visible damages. In situation of discovering any damages please contact by written your supplier. Unpacking The scale is packed and delivered on the pallet. The loading and unloading device from the truck should be preceded using correct equipment.
- Page 6 Arrangement and usage requirements Arrangment To obtain the most accurate weighted value, the scale should set up only in places which pass the following conditions: Surface must be flat and vertical. Slope cannot be bigger than 2°. Surface must be stable and not exposed for vibrations. Do not expose for long effect of sun.
- Page 7 Operating KPZ 71 Daily operating Before using, please check the device for its working condition, is it ready for handling and free of visible damages, specifically on wheels and forks. Please check the battery and follow electronic and charger guidelines. While handling the device not a lot of effort should require.
- Page 8 Self-acting display test After switch on the scale, automatically will begin self-acting display test. Visible counting from 99999 to 000000. Please pay attention to all signs and symbols on the display which are showing up on full screen, to avoid receiving an incorrect values. After displaying zero the scale is ready to use.
- Page 10 Power Supply Accumulator supply Scale on the handpallet KPZ is delivered with the charger. Delivered charger supply the energy to built-in accumulator. Charging: Protect the handpallet from moving. When the display is turned off you may proceed and connect the charger to on-site power supply (230V), other end plug in to the socket located in the front of the device.
- Page 11 Maintenance, storage and carrying Maintenance For better maintenance never use strong care products no strong detergents should be used (solvents etc.) Scale should be carried by soft and damp cloth and/or soft detergents. No fluids can enter inside of the scale. Storage Accumulator should be fully charged.
- Page 13 User Guide 8.0 Indicator Frontview of Indicator...
- Page 14 Indicator : Zero indication : Net weight indication : Low battery indication : Stable indication STABLE : Gross weight indication GROSS : Accumulation mode indication : Pretare indication ← → : Range indication (for multirange) : kg unit : peace unit, counting mode Set point indication:...
- Page 15 Keypad Function Hold for 1 sec. data output Printout / (Option) Communication settings Totalizing Modus selection / Function Switching between net and gross weight (net mode) switching units Switch between weight / unit weight (piece counting mode) Tare 1. Backlight 2.
- Page 16 Operating of the indicator Zero setting If the scale does not show 0.0 with no load, the display indication will be set to zero by pressing the button. This is up to 2% of the Max capacity possible. Tare Should the scale only display the weight of contents of a container, place an empty container on the scale and press the button.
- Page 17 General Functions →0← Weighing Modus ▼ 1 ▼ 6 →0← Reference piece count function -> 9.1 ▼ 1 Target weight function -> 9.2 Addition function -> 9.3 Hold function -> 9.4...
- Page 18 9.1 Reference Piece Count Function →0← ▼ 1 →0← 1. Selection of reference pcs ▼ 1 (10, 20, 50, 100, 200) →0← ▼ 1 →0← ▼ 1 1. Place the reference quantity ▼ 1 2. Put on pieces Piece ▼ 1 3.
- Page 19 9.2 Target Weight Function 1. Select the signal tone ⇒No signal tone ⇒Signal inside OK value ⇒Signal inside HI & LO value 1. Enter the desired values ⇒ ⇒ (0~9) ⇒ Hi Value (Hi = 3.000kg) (Lo = 1.000kg) Lo Value 1.
- Page 20 9.3 Addition Function & →0← →0← Accumulation Accumulation function function ▼ 1 ▼ 6 ▼ 6 ▼ 1 ▼ 1 ▼ 6 ▼ 1 ▼ 6 automatic addition No. of additions No. of additions ▼ 1 ▼ 3 ▼ 6 ▼...
- Page 21 →0← Delete addition ▼ 6 ▼ 1 ▼ 3 The total weight is printed in print format. Press Key for 2 seconds. 3 times beep signal sounds. →0← Number of The accumulation data is cleared and RS-232 does not output additions MC printing format.
- Page 22 10 Advanced Features 10.1 Backlight / Zero / gravity value for 1 sec. ⇒ ⇒ = save (0~9) (9~0) ⇒ ⇒ →0← = abort ▼ 1 1 sec. LCD backlight Zeroindication ± Gravitation value LCD backlight 0~9d Automatically ...
- Page 23 Error messages E0 ⇒ System error. (Contact service) E1 ⇒ Zero range is higher than 10% of maximum capacity while switching on the scale. (example: Scale is loaded while turning on, problem with plugging in, load cell is damaged) E2 ⇒ Zero range is lower than 10% of maximum capacity while switching on the scale.
- Page 24 S1022 WSP 2200_en 310117...