Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for logitrans WSP 2200
Summary of Contents for logitrans WSP 2200
- Page 1 WSP 2200 Weighing scale pallet truck Quick guide...
-
Page 2: Table Of Contents
Contents 5.5 Operation ......................2 6.0 Battery and charger ..................3 10.2 Actual battery voltage ................3 5.4 Starting up scale ....................3 8.2 Display and Keypad ..................4 Choice ”Set point indication” ................4 8.3 Keypad ......................5 10.1 Backlight of display .................. 6 9.0 Program shift / Choice .................. -
Page 3: Operation
5.5 Operation The weighing scale pallet truck has to be placed on an even surface. The load centre of the load has to be centred on the forks and, if possible, placed towards the vertical flat iron (if placed on a EURO pallet). Do NOT leave the load on the forks for longer periods (e.g. -
Page 4: Battery And Charger
6.0 Battery and charger Up to 250 operating hours per charging. Battery indicator indicates whether the battery voltage is low. Press for 1-2 seconds, and the actual battery voltage will be visible. Battery is being charged Charger connected. LED is red Battery is minimum 75% charged. -
Page 5: Display And Keypad
8.2 Display and Keypad Arrow Display Explanation The scale is in the zero position. Reset scale STABLE The weight is stable (no change of weight) Shows net weight (tara activated) GROSS Shows gross weight Contents in memory Battery voltage is too low Tara is entered (Pretara) Showing weight in kilogram Number of pieces... -
Page 6: Keypad
8.3 Keypad Explanation Print (this model has no printer) Sum / Result Enter Modus selection / Switching between programs Switching between net and gross weight Scroll to the left Not in use Switch between weight / number of units Counting down (9-0) Tara Pretara Scroll to the right... -
Page 7: Backlight Of Display
10.1 Backlight of display The backlight can be set according to need. bl.Auto Backlight automatically set, when the scale is used bl.on Backlight switched on constantly bl. off Backlight switched off constantly Press for 2 seconds. Press again Actual settings are shown Scroll in the menu Exit and save by pressing After this... -
Page 8: Program Shift / Choice
9.0 Program shift / Choice Use this button to shift between the different programs. Each press shifts to next picture. S1056... -
Page 9: How To Use
8.4 How to use Tara If the scale only has to display the weight of e.g. contents of a container, place an empty container/pallet on the scale and press .Now the scale shows 0 kg. The display shows the symbol NET. After filling in the contents, only the contents of the container/pallet are shown. -
Page 10: Simple Count Function
9.1 Simple count function →0← ▼1 1. Scroll and select reference number. →0← to scroll in menu. ▼1 (10, 20, 50, 100, 200) →0← ▼1 2. Place the reference number on the scale E.g. 10 units. Lift / press 3. Scale is ready to count N Number 4. -
Page 11: Target Weight Function
9.2 Target weight function 1. Select signal tone (beep) 2. Open Hi-Lo by pressing to scroll in menu = No beep = Signal inside OK value = Signal inside HI/LO value 3. Confirm choice (e.g. b1) with 4. Enter requested weight, first in HI, then LO. -
Page 12: Accumulation Function
9.3 Accumulation function & ACC 1. First lift 1. Press and scale is ready Weight 2. Lift the load. Weight is shown 3. Press to save the result Number is shown. After 0,5 sec., Number of lifts weight of load is shown. 4. -
Page 13: Acc 2. Automatic Addition Function
ACC 2. Automatic addition function Same as ACC 1. But for ACC 2 it is automatic instead of pressing NOTE! It is important to have an even ground, otherwise the scale will make error counting. ACC 2. First lift 1. Press to change to ACC 2 2. -
Page 14: Error Messages
11 Error messages E0 system error (Please contact Logitrans After Sale Service) E1 Zero range is higher than 10% of maximum capacity while switching on the scale. (Scale is loaded, while switching on. Problem with electric switch. Weighing cell is damaged*) E2 ⇒...