Table of Contents
Advertisement
Installer Menu (Cont.)
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the TV is turned ON. This feature is useful for
an in-house information channel, since the TV will always select
that volume level when it is turned ON. The range of values is 0
to 63, 255. If set to 255, the last volume level before the TV was
turned OFF will be the current volume level when the TV is turned
ON again.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range
is from 0 to 63. The factory default is 0, which provides the full
range of volume control, if item 009 MAX VOLUME is set to 63. It
is recommended to set the same value on every TV.
Note: The minimum volume level cannot have a value setting
higher than the maximum volume level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb
others. The value range is 0 to 63, with 63 as the default, which
gives the user the full range of volume control, if item 008 MIN
VOLUME is set to 0. It is recommended to set the same value on
every TV.
Note: The maximum volume level cannot have a value setting
lower than the minimum volume level (described above).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot
be muted. If set to 0, sound can be muted.
011 - KEY DEFEAT
If set to 1, Key Defeat is enabled, which means that, with the
exception of the input list, end users cannot access or navigate
within the on-screen menu(s) from the display panel; i.e., joystick
button menu navigation functions (input list excepted) will not be
available. Set to 0 to disable Key Defeat. Note that all IR features
remain functional regardless of this setting; users can always
access the menus by pressing MENU on the remote.
012 - IR BANKS EN. (IR Banks Enable)
For direct access to a particular channel bank. When enabled, you
can access a channel bank by inputting the discrete IR code for
that bank.
Note: This item is not available in the Installer Menu when item
027 HOSPITAL MODE is set to 0.
40
013 - SCAN MODE
When set to 1 (default), allows TV to be turned ON when Channel
Up/Down buttons are pressed on pillow speaker. Also, TV will turn
OFF when Channel Up/Down key is used to tune above or below
Channel Map pivot point. By default, Channel Map pivot point is
between the highest and lowest channel in the Channel Map (also
see item 014 STRT CH IN SM). Set to 0 to disable.
Note: This item is only applicable when the TV is in PTC-CTV
Mode.
014 - STRT CH IN SM (Start Channel in Scan Mode)
Only valid when item 013 SCAN MODE is set to 1 (enabled).
When set to 1, forces Channel Map pivot point to be between the
RF channel designated in item 004 STRT CHANNEL and next
lower channel in the Channel Map. Set to 0 to disable (default).
Note: This item is not available in the Installer Menu when item
013 SCAN MODE is set to 0.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature may be used. If set to 0, the
Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, the Timer function is available to the end user and
enabled continuously. Set to 0 to disable On/Off timers.
Note: The TV clock must be set in order for timers to be used.
017 - ALARM
Gives the installer the option of making the Alarm function available
to the end user. If set to 1, the Alarm function is available to the end
user. Set to 0 to disable the Alarm function.
Note: The TV clock must be set before the Alarm function will
work.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on "bed
number" in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Note: When item 027 HOSPITAL MODE is set to 0, both the
IR code that will control the TV and the speaker selection are
determined by this item (default = 1). Set this item as required to
enable Zenith Bed 1 or Bed 2 IR codes and speaker selections.
Values
IR Mode
0 – 1
Zenith (Hospital)
16 – 24
Multi-code Remote
64 – 65
Zenith (Hospital)
Note: See Reference section, "LG Pro:Centric Patient Remote
and Pillow Speaker," for additional information. Also, see
documentation for the accessory package that includes the multi-
code remote.
Bed #
Speaker
1 – 2
TV Only
1 – 9
TV Only
1 – 2
Pillow Only
206-4271
Advertisement
Chapters
Table of Contents
Troubleshooting
