Page 1
INSTALLATION AND OPERATION MANUAL Jandy Pro Series Levolor ® Electronic Water Leveler Model K-2100 WARNING FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly.
Page 2
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 2 ENGLISH Models K-2100 Installation and Operation Manual...
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 3 ENGLISH Models K-2100 Installation and Operation Manual Table of Contents Section 1. Safety Information ...... 4 Section 2. System Description ....5 2.1 Electrical Specifications .......5 Schematic ............6 Section 3. Installation Instructions ..... 7 3.1...
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 4 ENGLISH Models K-2100 Installation and Operation Manual Section 1. Safety Information IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF PROPERTY DAMAGE OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS...
Section 2. System Description Valve The K-2100 requires one (1) 24VAC solenoid valve. Levolor II by Jandy Model K-2100 is a computer- The Jandy-supplied valve (Part No. SOL100) has a controlled fill device that detects low water conditions. pressure rating that cannot exceed 125 PSI.
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 6 ENGLISH Models K-2100 Installation and Operation Manual Schematic This section contains a schematic for the K-2100. Figure 1. K-2100 Schematic...
Open the box and check to see that it contains the For 220 volt operation, connect the black wire to contents listed above. If it does not, contact your Jandy line 1 and connect the black wire with the yellow dealer or Zodiac Pool Systems, Inc.
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 8 ENGLISH Models K-2100 Installation and Operation Manual Changing Wiring for 110 Volt Grounding Operation Connect the green ground wire marked to the grounding terminal of your electrical service or supply...
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 9 ENGLISH Models K-2100 Installation and Operation Manual Installing the Valve and Relay Flow Control NOTE Install the valve with the directional water flow arrow pointing in the appropriate direction. The directional water flow arrow is located on the inlet side of the valve. A 24VAC solenoid valve will provide water from a supply line to the fountain (or other environment: cooling tower, pond, reservoir, storage tank, etc.).
Page 10
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 10 ENGLISH Models K-2100 Installation and Operation Manual Five (5) Status Lights Red Wires to Low Water Cutoff AC Relay (24VAC) Blue Wires to Fill Valve Black Wire to Power (24VAC)
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 11 ENGLISH Models K-2100 Installation and Operation Manual Installing the Sensor NOTE Sensor wires must be continuous and not SIDE VIEW spliced. Solder all low voltage wire connections when possible and always use grease-filled Cable wire nuts on low voltage connections. NOTE When mounting a slip style sensor in a static Extension Pipe pipe, glue 1" fittings with 793 IPS brand ABS/ PVC glue. Do not glue 2" fittings. Do Not Submerge Mount the slip sensor vertically in a static pipe.
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 12 ENGLISH Models K-2100 Installation and Operation Manual Static Pipe Installation in a New Fountain Figure 9 shows a static pipe installation in a new fountain (or other environment: cooling tower, pond, reservoir, storage tank, etc.).
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 13 ENGLISH Models K-2100 Installation and Operation Manual Section 4. Operation Filling Sensor Power Controller Lights The controller has five (5) lights. See Figure 10 and Table 2, LED Indicators.
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 14 ENGLISH Models K-2100 Installation and Operation Manual Change Fill Time for Safety Lockout Mode To change the pre-set factory Fill time, turn off the power to the control box, open it up, and cut one or both jumpers on the circuit board.
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 15 ENGLISH Models K-2100 Installation and Operation Manual Section 5. Troubleshooting Test Operation of Control Unit 5.2.1 Disconnect Sensor, Valve and Relay Tools required: AC volt meter and No. 6 Phillips Shut power off to the control box.
Page 16
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 16 ENGLISH Models K-2100 Installation and Operation Manual 5.2.2 Observe Operation 5.2.3 Manual Valve Override There is a manual ON/OFF lever on the valve body Restore power to the control box and observe the located just below the solenoid.
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 17 ENGLISH Models K-2100 Installation and Operation Manual Fill Valve Will Not Turn OFF Fill Valve Will Not Turn OFF Is the fill light on? Disconnect the yellow wire at the controller from the black wire at the sensor.
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 18 ENGLISH Models K-2100 Installation and Operation Manual Fill Valve Will Not Turn ON Fill Valve Will Not Turn ON Verify correct voltage supply. Is the power light on? Is the sensor light on? Turn on power.
Page 19
Jandy Pro Series Levolor II Electronic Water Leveler ® Page 19 ENGLISH Models K-2100 Installation and Operation Manual Notes...