Page 1
OWNER’S MANUAL ENGLISH FRANÇAIS ESPAÑOL Jandy Pro Series Nicheless LED Underwater Light WARNING FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist.
RS Control System ....8 ® Wire Gauge and Length ..........9 Wiring to a Switch............10 Twelve (12) Volt Installation.........10 Section 5. Jandy Pro Series Nicheless Underwater LED Light Operating Instructions ........11 Light Synchronization ..........11 Operating the Light ............12 Section 6.
888.647.4004 (Canada) CAUTION Except when the Jandy Pro Series Nicheless Underwater LED Lights ® are installed in an area of the swimming pool that is not used for swimming and the lens is adequately guarded to keep any person from...
General Description Product Overview This manual provides instructions for installing and replacing the Jandy Pro Series Nicheless Underwater LED Lights for pool and spa use. CAUTION The Jandy Pro series nicheless LED underwater lights are not serviceable and therefore contain no serviceable parts. In order to prevent risk of property damage and/or injury, no service should be attempted to the light in the event of a malfunction.
NOTE: Jandy Pro Series Nicheless Lights are Low Voltage and do not have any exposed metal and as such do not require a separate ground or bonding wire.
The light face must be completely snug with the light fitting without any protrusion from the light fixture. Figure 1. Jandy Pro Series LED Light Installation with Standard 1.5” ® Plastic Fitting Use the chart below to determine the appropriate pipe length for your installation.
Page 7
NOTE: When using a 1 1/2” MIP fi tting on the back of a SP-1022 or SP-1408 Wall Fitting, the interior of the Spears and Dura MIP are too small for use with the Jandy Pro Series Nicheless LED Lights.
Wiring to an AquaLink Controller ® The Jandy Pro Series Nicheless LED Lights can be controlled by an AquaLink controller. Connect the transformer powering the lights to one of the auxiliary relays in the AquaLink. Refer to Figure 4 to connect the Jandy Pro Series Nicheless LED...
Nicheless Underwater LED Lights | Owner’s Manual Wire Gauge and Length CAUTION Jandy Pro Series Nicheless Underwater LED Lights are low voltage ® fixtures. Improper wire gauge and wire length can effect the performance of these products. Follow the guidelines below to determine the proper operation and optimum performance of the lights.
Nicheless Underwater LED Lights | Owner’s Manual WARNING RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, which could result in serious injury or death. The Jandy Pro Series Nicheless LED Lights are only available for 12-volt AC power. For supply connection, use only an isolating low voltage power supply with ungrounded output, evaluated and listed by a NRTL for swimming pool use.
Wiring LED Lights to a 12 Volt Magnetic Transformer NOTE A magnetic low-voltage dimmer switch or dimming relay may be used when Jandy Pro Series Nicheless WHITE ONLY lights are installed. Jandy Pro Series color lights are NOT DIMMABLE and are NOT COMPATIBLE with dimmer switches or dimmer relays.
Pro Series Nicheless ® Underwater LED Light systems wired to separate switches, perform the above actions on all of their switches simultaneously. All Jandy Pro Series Nicheless Underwater LED Lights will synchronize automatically if activated by the same switch. No other accessories...
ENGLISH Page 13 Nicheless Underwater LED Lights | Owner’s Manual Section 6. S-Series Nicheless Underwater LED Light Operating Instructions Light Synchronization for S Series Lights 1. Turn the light ON and wait for 20 seconds. The lights will first come on white for 10-15 seconds and then return to the color mode it was on prior to being turned off.
Page 14 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual 2. The lights have memory. If the lights are off for 10 seconds or more, the next time the lights are turned on, they will go to white for approximately 10-15 seconds and then return to the last color mode they were on prior to being turned off.
Page 15
ENGLISH Page 15 Nicheless Underwater LED Lights | Owner’s Manual Sequence Color Modes (Universal ColorLogic emulation) ® Order Color Show - Voodoo Lounge Deep Blue Sea Royal Blue Afternoon Skies Aqua Green Emerald Cloud White Warm Red Flamingo Pink Vivid Violet Sangria Dark Purple/Red Color Show - Twilight Color Show - Tranquility...
Page 16 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Section 8. P-Series Nicheless Underwater LED Light Operating Instructions Operating the P-Series Lights 1. Turn the light ON and wait for 20 seconds. The lights will first come on white for a few seconds and then return to the color mode it was on prior to being turned off.
ENGLISH Page 17 Nicheless Underwater LED Lights | Owner’s Manual Cycle Color Modes for P-Series Lights (IntelliBrite emulation) ® Number Mode ® Party Mode Romance Mode Caribbean Mode American Mode California Sunset Royal Mode Blue Green White Magenta Hold : Saves the current color choice during a color show Recall: Turns on last saved color selection selected in position #13 * These 2 Modes are specifically used with advanced control systems and not...
Page 18 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Section 10. Troubleshooting Use the troubleshooting information in the following table for suggestions. Symptom Problem Corrective Action All lights fail to illuminate Lights are not reciev- Check 120VAC power supply ing power into transformer.
Page 19
ENGLISH Page 19 Nicheless Underwater LED Lights | Owner’s Manual NOTES...
Page 20
Zodiac Pool Systems, Inc. 2620 Commerce Way, Vista, CA 92081 1.800.822.7933 | www.ZodiacPoolSystems.com Zodiac Pool Systems Canada, Inc. ETL LISTED CONFORMS TO 2115 South Service Road West, Unit 3 Oakville, UL STD 676 ON L6L 5W2 CERTIFIED TO CAN/CSA C22.2 NO.89 1.888.647.4004 | www.ZodiacPoolSystems.ca ZODIAC ®...