Subscribe to Our Youtube Channel
Related Manuals for Sebury sReader-w
Summary of Contents for Sebury sReader-w
- Page 1 / sReader-s User Manual Please read this instruction completely and keep it properly...
-
Page 2: Product Introduction
Product Introduction sReader adopts high-strength ABS plastic appearance.EM,HID and IC card reading are supported.Bluetooth analog card Wiegand output function of mobile phone, built-in high integration micro-controller and simple circuit are applied. safety and reliability are assured. sReader is cost effective and durable, suitable for office, communiy and other context using. - Page 3 Dimension: 120 * 85 * 23mm sReader-s Dimension: 107 * 48 * 23mm Ingress protection: IP65 (water and dust-resistant) Wires and Instruction...
-
Page 4: Packing List
Packing List sReader-w / sReader-s User Manual Please read this instruction completely and keep it properly User Manual*1 Card Reader*1 Punch Sticker*1 Screw Hole Decoration Piece*1 Self Tapping Screw KA4*25mm ( sReader-w*4 ） Expansion Rubber Bung Φ6*24mm ( sReader-w*4）... -
Page 5: Installation
Installation Drill Installation Holes Stick the punch sticker on the wall. Drill 2 Φ6mm intallation holes with purcussion drill with the depth of 26mm.（4 holes for sReader-w ）... - Page 6 Drill the Hole for Outlet Drill Φ10mm hole for outlet with the depth according to the practical situation of electric lines.
- Page 7 Click Expansion Rubber Bung Click 2 expansion rubber bungs into the installation holes （4 expansion rubber bungs for sReader-w）...
- Page 8 Fix the Back Shell Fix the back shell on the wall with 2 K4*25 self tapping screws（4 screws for sReader-w） （The percussion drill,hammer and screwdriver in figure2,3 and 4 should be self prepared.）...
- Page 9 Connect Cables Put the outlet cables through the Φ10mm hole and connect the needed cables.(Pack the useless cables with the insulating tape.)
- Page 10 Install the Front Shell and Screw Hole Decoration Piece Put the front shell on the back shell. Install the tamper screw from the bottom of the device with screwdriver and stick the screw hole decoration piece onto the device.
-
Page 11: Functional Description
Functional Description 1. When swiping the card, the indicator light turns green and the reader has a steady beep.Then indicator light turns red, wiegand signal is output at the same time. 2. When the LED line is lowered, the indicator light turns green; when the LED line is set high, the indicator light turns red. - Page 12 Mobile Phone Operating 1.Download and install APP Scan the following QR code, or Android search：“Access Control ”, Apple store search：“BleAccess”. Android Search "BleAccess" in Apple store to download the BLE App. 2. Administrator's Mobile Phone Operations Only one administrator is permitted on sReader. Administrators must be added first, other users can be added by administrators.
- Page 14 ⑶ Click the device name at the top of Figure 3.Enter a new device name in the dialog box for modifying the device name( Figure 4). Click OK to confirm the new name(Figure 5) as shown in Figure 6. The last modified name is displayed when sharing to other users.
- Page 16 Administrators add users as follows: ⑴ Click "User Management" in Figure 6 and enter the list of users as shown in Figure7. Administrator is automatically added, the name of administrator can not be modified. ⑵ Click "Add User" to add a user bar, as shown in Figure 8.
- Page 17 ⑶ Click the user bar to enter the user's QR code page as shown in Figure 9. After modifying the user's name, click "Change user information", the QR code information will be changed accordingly. After modification, the QR code contains all the information assigned to this user (Figure 10).
- Page 18 Administrators delete users as follows: Swipe left the user bar to see a "delete" button, click "delete" and "confirm delete" to delete the user from the list.
- Page 19 3.Other users add device Administrator opens APP and enters the page in Figure 10, showing the user's QR code. The user opens the APP and enters the page in Figure 1. clicking on the "Scan QR Code" to scan the user's QR code on the administrator's mobile phone. Adding devices is successful when the interface is shown as Figure 3.
- Page 22 5.Device upgrade When the product firmware has a new version, APP will appear a prompt icon. Click on the red dot icon shown as in Figure 17. Click "OK" for the dialog box (Figure 18). The firmware will start to upgrade(Figure 19). The upgrade will be completed when the mobile interface is shown as in Figure 19.
- Page 24 6.APP FAQs ⑴ The user's QR code has been obtained from the administrator. Why can't I open the door? Bluetooth is not on or too far away from the device, the signal is too weak. ⑵ How can I suspend the use of one user without deleting the user? Just change the user's name.
- Page 25 connect the device successfully. After that , the original administrator connection will be automatically failed. ⑸ Will the original users be lost when Replace mobile phones, administrators or re-install APP ? No, the user information is stored in the device. After entering the management user mode, APP will download the device data again, then you can modify the user information or add new users.
- Page 26 New Arrival - sPad Exit Button Enjoy My Intelligent Access Control System...
- Page 27 New Arrival - mReader All-Metal Access Control Card Reader The Redifinition of Access Control Card Reader...
- Page 28 E-Instruction v1.1 2020/8/20...
Need help?
Do you have a question about the sReader-w and is the answer not in the manual?
Questions and answers