Vat Set Up - Welbilt Frymaster YUM K3000 Operation Manual

1.4 K3000 Setup Mode
Setup mode allows the Controller to be set for language displays, vat sizes, and temperature range displays. Follow the
steps below to enter and navigate Vat Setup.

Vat Set Up

Left Display Right Display
OFF OFF
Product Setup Blank
Vat setup Enter code
System
Blank
Language English
2nd language English
Locale Non-ce
ENERGY Gas
type KJ3 Full
System volume 9
Tempr format F
Exit Melt Tempr 100F
Setback tempr 250F
Fresh oil None
waste NONE
DRAIN SWITCH NO
RECOVERY DISABLED
ALARM
Exit Exit
OFF OFF
Time/date
Blank
Time entry time
Date format Mm/dd/yy
Enter date date
Exit Exit
Continued on the following page
Press and hold until Product Setup is displayed.
Press  to scroll to Vat setup and press . Product setup is described on pages 1-10
through 1-13.
Enter 3228.
Press button or press  to scroll to Time/Date, Filter, E-Log, Change Password or Edit
Alarm Names. With desired choice displayed, press . If SYSTEM is not chosen skip to
the relevant selection.
Press  to scroll to choice and press .
Press  to scroll to choice and press . (This option allows another language to be
toggled easily from the front panel (ex. Spanish as a second language.)).
Press  to scroll to choice Non-CE or CE and press .
Press  to scroll to choice Gas or Electric and press .
Press  to scroll choices: the choices are: Gas-KJ3/CF-FULL, 118G/D63 FULL, H55
FULL, H55 SPLIT, MJ45 FULL, MJ45 SPLIT, HV75 FULL, HV105 FULL, 114/HD50
FULL, HD60 FULL, HD65 FULL D80 FULL, 11814 FULL and MJ35 FULL, . Electric-
118E/RE80 FULL, FPRE117 FULL, FPRE117 SPLIT, FPRE114 FULL and FPRE114
SPLIT, 11817 FULL, FPRE122 FULL, FPRE122 SPLIT FPC128 FULL, FPC128 SPLIT
and FPC136 FULL. With the vat size of the fryer controlled by the Controller displayed,
press .
Sets sound level for Controller. Enter level, 1-9 (0=Lowest/ 9=Loudest). Press .
Press  to scroll choices: F for Fahrenheit; C for Celsius. Press .
Use numbered buttons to change default setting (use 10 for 0). Press . (This is the
temperature for the fryer to exit the melt cycle.) Default is 100F (38C).
Use numbered buttons to change default setting (use 10 for 0). Press . (This is the
temperature during setback or idle mode.) Default is 250F (121C).
Press  to scroll choices JIB, Bulk-RTI, Bulk-F (Frontline) or None. Press .
All fryers except OCF should be set to NONE.
Press  to scroll choices JIB, Bulk-RTI, Bulk-F (Frontline) or None. Press .
All fryers except OCF should be set to NONE.
Press  to scroll choices YES and NO. (This is if a drain switch is installed.) Press .
Press  to scroll choices DISABLED and ENABLED. (This is a recovery alarm that
locks out the fryer if the fryer does not heat properly. The default is disabled). Press .
Press button.
None required.
Press .
Use numbered buttons to change time (use 10 for 0). Press .
Press  to scroll choices. With the date format displayed, press .
Use numbered buttons to change date (use 10 for 0). Press .
Press  button once and press  to scroll to System, Time/Date, Filter, E-Log, Change
Password or Edit Alarm Names. With desired choice displayed, press  or press the
Scan button once to return the Controller to OFF.
1-4
Action
NOTE:
NOTE: