Related Manuals for Teknik Mahattan View 5423446
Summary of Contents for Teknik Mahattan View 5423446
- Page 1 Teknik www.teknikoffice.co.uk Sit and surf. Mahattan View L-Shaped Desk Model 5423446 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 6-27 Français 28-31 Skip the power trip. Español 32-35 This time. Safety 36-38 Warranty Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. DESK TOP (1) HUTCH TOP (1) DRAWER BOTTOM (1)
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. CABINET RIGHT - 1 CABINET LEFT - 1 DRAWER RIGHT - 1 DRAWER LEFT - 1 LARGE HIDDEN LARGE CAM SMALL HIDDEN SMALL CAM CAM - 19 SCREW - 19 CAM - 8...
- Page 5 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. BLACK 1-7/8" HEX HEAD SCREW - 2 BLACK 1-9/16" HEX HEAD SCREW - 10 BLACK 1-3/8" HEX HEAD SCREW - 5 BLACK 1-1/2" HEX HEAD SCREW - 19 BLACK 1-3/8"...
- Page 6 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Some assembly Push nineteen LARGE HIDDEN CAMS (5) into the LEFT å (and snacks) required. END (D), REAR PANEL (E), UPRIGHT (G), RIGHT END (H), HUTCH ENDS (M and N), HUTCH UPRIGHTS (O and P), and DIVIDER (EE).
- Page 7 Step 2 Fasten the CABINET RIGHT (1) to the UPRIGHT (G). Use å three BLACK 1/2" FLAT HEAD SCREWS (28). Fasten the CABINET LEFT (2) to the LEFT END (D). Use å three BLACK 1/2" FLAT HEAD SCREWS (28). Use these holes. Roller end BLACK 1/2"...
- Page 8 Step 3 Separate the WASHER from the MAGNETIC CATCH (11). å Fasten the MAGNETIC CATCH (11) to the DESK TOP (A) exactly as å shown. Use two BLACK 9/16" FLAT HEAD SCREWS (27). Fasten the WASHER to the FLIP DOWN DOOR (F) exactly as å...
- Page 9 Step 4 Insert two WOOD DOWELS (9) into the UPRIGHT (G) and å RIGHT END (H). Fasten the DIVIDER (EE) to the UPRIGHT (G) and RIGHT END (H). å Tighten two HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the UPRIGHT and RIGHT å...
- Page 10 Step 5 Insert two WOOD DOWELS (9) into the DESK TOP (A). å Insert two METAL PINS (10) into the FLIP DOWN DOOR (F). å Place the REAR PANEL (E) onto one of the METAL PINS in the FLIP DOWN DOOR (F). å...
- Page 11 Step 6 Fasten the REAR PANEL (E) to the LEFT END (D) and å UPRIGHT (G). Tighten four BLACK 1-1/2" HEX HEAD Just think. The sooner SCREWS (22) using the L-WRENCH (15). you do this, the sooner you do something else. Insert one of the GROMMETS (12) into the large hole in å...
- Page 12 Step 7 Insert four WOOD DOWELS (9) into the HUTCH å TOP (L). Fasten the HUTCH ENDS (M and N) and HUTCH UPRIGHTS (O and P) to the HUTCH TOP (L). Tighten eight HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the HUTCH TOP å...
- Page 13 Step 8 Slide the HUTCH BACK (Q) down into the grooves in the HUTCH å TOP (L) and HUTCH ENDS (M and N). Insert four WOOD DOWELS (9) into the HUTCH ENDS (M and N) å and HUTCH UPRIGHTS (O and P). Fasten the HUTCH BOTTOM (K) to the HUTCH ENDS (M and N) å...
- Page 14 Step 9 NOTE: Do not completely tighten the SCREWS in this step. å Slide the MOLDINGS (AA and BB) onto the LEFT RETURN FRAME (Y). å Fasten the MOLDINGS (AA and BB) to the LEFT RETURN FRAME (Y). Tighten å six BLACK 7/16"...
- Page 15 Step 10 NOTE: Do not completely tighten the SCREWS in this step. å Slide the RIGHT RETURN FRAME (X) into the MOLDINGS (AA and BB). å Fasten the RIGHT RETURN FRAME (X) to the MOLDINGS (AA and BB). å Tighten six BLACK 7/16" HEX HEAD SCREWS (29) using the L-WRENCH (15). BLACK 7/16"...
- Page 16 Step 11 Fasten the HUTCH MOLDING (CC) to the RETURN å FRAMES (X and Y). Tighten four BLACK 7/16" HEX Now might be a HEAD SCREWS (29) using the L-WRENCH (15). good time to refresh your drink. NOTE: Position the HUTCH MOLDING (CC) exactly å...
- Page 17 Step 12 Fasten the HUTCH BOTTOM (K) to the RETURN å FRAMES (X and Y) and HUTCH MOLDING (CC). Tighten fi ve BLACK 1-3/8" HEX HEAD SCREWS (23) using the L-WRENCH (15). NOTE: Start each SCREW a few turns before å...
- Page 18 Step 13 Fasten the RETURN TOP (B) to the RETURN FRAMES (X å and Y) and UPPER RETURN MOLDINGS (BB). Tighten ten BLACK 1-9/16" HEX HEAD SCREWS (21) using the L-WRENCH (15). NOTE: Start each SCREW a few turns before tightening any å...
- Page 19 Step 14 With someone's help, carefully stand your unit upright. å Insert two WOOD DOWELS (9) into the RETURN BACK (J). å Fasten the RETURN BACK (J) to the RETURN TOP (B). Tighten four BLACK å 1-1/2" HEX HEAD SCREWS (22) using the L-WRENCH (15). NOTE: Start each SCREW a few turns before tightening any of them.
- Page 20 Step 15 Fasten the LOWER DESK MOLDING (DD) to the DESK å FRAME (Z). Tighten two BLACK 7/16" HEX HEAD SCREWS (29) using the L-WRENCH (15). Fasten the LOWER DESK MOLDING (DD) to the LEFT å RETURN FRAME (Y). Tighten two BLACK 7/16" HEX HEAD SCREWS (29) using the L-WRENCH (15) Surface with holes BLACK 7/16"...
- Page 21 Step 16 NOTE: You may need someone's help in this step. å Insert two WOOD DOWELS (9) into the RETURN TOP (B). å Position the DESK TOP (A) into place so the UPRIGHT (G) sits down å onto the WOOD DOWELS in the RETURN TOP. Fasten the UPRIGHT (G) to the RETURN TOP (B).
- Page 22 Step 17 Fasten the RETURN BACK (J) to the DESK TOP (A). å Tighten three BLACK 1-1/2" HEX HEAD SCREWS (22) using the L-WRENCH (15). Fasten the RETURN BACK (J) to the RIGHT END (H). å Tighten two BLACK 1" TAPERED MACHINE SCREWS (26) using the L-WRENCH (15).
- Page 23 Step 18 Fasten the END MOLDING (C) to the LEFT END (D). Tighten å three BLACK 1" TAPERED MACHINE SCREWS (26) using Almost time to the L-WRENCH (15). celebrate! With a nap. The holes are closer to this edge. BLACK 1" TAPERED MACHINE SCREW (3 used in this step) Page 23...
- Page 24 Step 19 Turn eight SMALL CAM SCREWS (8) into å the DRAWER FRONT (R). Push eight SMALL HIDDEN CAMS (7) å into the DRAWER SIDES (S and T) and DRAWER BRACES (W). (8 used) Arrow (8 used) The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
- Page 25 Step 20 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Surface with HIDDEN CAMS Groove Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Fasten the DRAWER SIDES (S and T) and DRAWER å...
- Page 26 Step 21 Fasten the DRAWER RIGHT (3) to the RIGHT DRAWER SIDE (T). å Use three BLACK 1/2" FLAT HEAD SCREWS (28). Fasten the DRAWER LEFT (4) to the LEFT DRAWER SIDE (S). Use å three BLACK 1/2" FLAT HEAD SCREWS (28). Use these holes.
- Page 27 Step 22 Insert the GROMMET WITH CAP (14) into the large hole in the DESK TOP (A). å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the å...
- Page 28 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...