Advertisement
Quick Links
Advertisement
Related Manuals for Teknik Market 5425767
Summary of Contents for Teknik Market 5425767
- Page 1 Teknik We're in your corner. Market L-Shaped Desk Model 5425767...
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-20 Hammer Not actual size Français 21-24 Español 25-28 Skip the power trip. Safety 29-30 This time. Warranty Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. LEFT END LEG (1) LARGE DRAWER BACK (1) FRONT LONG BRACE (1)
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) EXTENSION RAIL - 2 EXTENSION SLIDE - 2 DRAWER RIGHT - 1 DRAWER LEFT - 1 CAM SCREW - 17 HIDDEN CAM - 17 CABINET RIGHT - 1 CABINET LEFT - 1...
- Page 5 Hardware Usage Guide HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL NOTE: Various CAM SCREWS or a CAM DOWEL may be used. Turn the CAM SCREW or gently tap the CAM DOWEL until the shoulder is against the surface of the part.
- Page 6 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Turn eight CAM SCREWS (7) into the LEFT END LEG (A) å and LEFT UPRIGHT LEG (B). (8 used) Page 6...
- Page 7 Step 2 Fasten the CABINET RIGHT (5) to the LEFT UPRIGHT LEG (B). Use three BLACK 1/2" FLAT HEAD SCREWS (19). å Fasten the CABINET LEFT (6) to the LEFT END LEG (A). Use three BLACK 1/2" FLAT HEAD SCREWS (19). å...
- Page 8 Step 3 Insert eight LARGE WOOD DOWELS (10) into the edges å of the BACK (C) and SHELF/BOTTOMS (D). Push eight HIDDEN CAMS (8) into the SHELF/BOTTOMS (D). å Arrow Arrow (8 used) Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
- Page 9 Step 4 Fasten the SHELF/BOTTOMS (D) and the BACK (C) to the å LEFT UPRIGHT LEG (B). Tighten four HIDDEN CAMS. Some assembly NOTE: Be sure the WOOD DOWELS in the SHELF/ å (and snacks) required. BOTTOMS and BACK (C) insert into the LEFT UPRIGHT LEG. Fasten the LEFT END LEG (A) to the BACK (C) and å...
- Page 10 Step 5 Fasten the LEGS (T and U) to the WIRE SHELF (Q). å Tighten four BLACK 1-3/16" HEX HEAD SCREWS (16) using the L-WRENCH (11). Fasten the LONG BRACES (R and S) to the LEGS (T and U). å Tighten four BLACK 1-3/16"...
- Page 11 Step 6 Carefully stand your unit upright. å Insert a LARGE WOOD DOWEL (10) into the exact hole shown å in the BRACE (P). Arrow Push a HIDDEN CAM (8) into the BRACE (P). å Fasten the BRACE (P) to the REAR LEG (U). Tighten two BLACK å...
- Page 12 Step 7 Fasten the LARGE TOP (V) to the LONG BRACES (R and S) å and LEGS (T and U). Tighten eight BLACK 1-3/16" HEX HEAD SCREWS (16) using the L-WRENCH (11). BLACK 1-3/16" HEX HEAD SCREW (8 used in this step) Page 12...
- Page 13 Step 8 Turn a CAM SCREW (7) into the SMALL TOP (O). å Side Step: Make Flip the SMALL TOP over and fasten it to the LEGS (A and B), å nachos. (Optional, but SHORT BRACE (W) and BRACE (P). Tighten the HIDDEN CAM recommended.) in the BRACE.
- Page 14 Step 9 Turn eight CAM SCREWS (7) into the DRAWER å FRONTS (E and F). Insert four SMALL WOOD DOWELS (9) into the edges å of the LARGE DRAWER SIDE (G and H) and LARGE DRAWER BACK (J). Push eight HIDDEN CAMS (8) into the DRAWER å...
- Page 15 Step 10 BLACK 1-3/16" FLAT HEAD SCREW (4 used in this step) i s h fi n r f a Groove Slide a DRAWER BOTTOM (N) into the grooves in the Fasten the SMALL DRAWER SIDES (K and L) to the å...
- Page 16 Step 11 Fasten a PULL (14) to the SMALL DRAWER FRONT (E). Use å two BLACK 13/16" MACHINE SCREWS (18). Flip the SMALL DRAWER over. Fasten the DRAWER RIGHT (3) to å the SMALL RIGHT DRAWER SIDE (L) and the DRAWER LEFT (4) to the SMALL LEFT DRAWER SIDE (K).
- Page 17 Step 12 BLACK 1-3/16" FLAT HEAD SCREW (4 used in this step) i s h fi n r f a Groove Fasten the LARGE DRAWER SIDES (G and H) to the Slide a DRAWER BOTTOM (N) into the grooves in å...
- Page 18 Step 13 Fasten a PULL (14) to the LARGE DRAWER FRONT (F). å Use two BLACK 13/16" MACHINE SCREWS (18). Fasten the EXTENSION SLIDES (2) to the LARGE å DRAWER SIDES (G and H). Use six BLACK 1/2" FLAT HEAD SCREWS (19). BLACK 1/2"...
- Page 19 Step 14 Push two FILE GLIDES (13) onto the top edges of the å LARGE DRAWER SIDES (G and H). Almost time to NOTE: This drawer is designed to hold letter size hangers. å celebrate! With a nap. t e r L e t Page 19...
- Page 20 Step 15 To insert the small drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the å rollers on the unit. Lift the front of the drawer up and slide it into the unit. To insert the large drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on å...
- Page 21 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...