Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kantech KT-315
Summary of Contents for Kantech KT-315
- Page 1 KT-315 Door Controller Installation Manual DN2016-1809...
- Page 2 (90) days, whichever is longer. The original purchaser must promptly notify Kantech in writing that there is defect in material or workmanship, such written notice to be received in all events prior to expiration of the war- ranty period.
- Page 3 WARNING: Kantech recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not lim- ited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.
-
Page 4: Table Of Contents
Table of Contents Pre-Installation Information........................1 Copyright Information ........................1 Safety Instructions ........................1 Components Required to Install KT-315 ..................1 Technical Support........................2 KT-315 Compliance Specifications......................3 FCC & IC Compliance ......................... 3 CE Compliance Notice......................... 3 CE & RCM Compliance ....................... 3 UL Compliance Notice ......................... - Page 5 Mounting the KT-PC4216 ......................17 Installation and Wiring ....................... 17 Applying Power ......................... 18 Assigning the KT-PC4216 Module .................... 18 KT3-LCD - Kantech LCD Time & Date Display Module ................. 18 KT3-LCD Introduction........................ 18 KT3-LCD Specifications ......................18 Unpacking the KT3-LCD ......................18 Mounting the KT3-LCD......................
-
Page 6: Pre-Installation Information
Copyright © 2018 Tyco International Ltd. and its Respective Companies. All rights reserved. All specifications were current as of publication date and are subject to change without notice. EntraPass, Kantech and the Kantech logo are trademarks of Tyco International Ltd. and its Respective Companies. -
Page 7: Technical Support
Technical Support For technical assistance with the KT-315 and other Kantech products, contact technical support, Monday to Friday. • Follow this link and complete the online form: http://www.kantech.com/Support/Contact_Technical_Support_Advanced.aspx • Internet: www.kantech.com • E-mail: access-support@jci.com Latin America Contact hours - 08:00 to 20:00 (GMT - 3:00) -
Page 8: Kt-315 Compliance Specifications
All circuits are power limited with the exception of the battery leads. The following Kantech readers are UL1076 listed and can be used with the Kantech Model KT315 in a UL294 compliant installation: P225W26, P225KPW26, P225KPXSF, P225XSF, P325W26, P325KPW26, P325XSF, P325KPXSF, and P600. -
Page 9: Downloadable Firmware
Power outputs are supervised and individually protected against short-circuits and surges by self-resetting PTC. Locking devices are also supervised for short and open circuits. Built-in Combus Expansion The KT-315 supports expansion modules to add inputs, outputs and an LCD time and date display for Time & Attendance purposes. KT-PC4108 - 8-Zone Input... -
Page 10: Technical Specifications
AC Power Input 120/16 VAC, 40 VA, class 2 transformer Battery Back-up 1battery 12 VDC, 7 Ah, supervised, provides up to 12 hours of operation, Kantech BD7-12 battery tested for 4 hours standby for UL294 Operating From 2°C to 40°C (35°F to 110°F) -
Page 11: Kt-315 Controller And Accessories
4-Relay and Combus additional power supply module for KT-315 KT-PC4216 16-Output expansion module for KT-315 KT-RM1 External isolation relay SPDT for KT-315 output (RL1/RL2) (not UL listed) KT3-LCD Time & date LCD display unit for KT-315 KT-315CAB KT-315 black metal cabinet including KT- LOCK... -
Page 12: Installing The Kt-315
The KT-315 uses high performance communication, proper grounding must be provided to ensure proper operation. Make an earth ground connection to the cabinet of the KT-315 as per the requirements of your local electrical code. Wire the E- GND terminal on the KT-315 printed circuit board directly to that connection point. -
Page 13: Hooking Up Inputs
Up to 2 readers can be connected to a KT-315. They can be installed on one door to control both entry and exit or on two separate doors operating independently to control one-way access. -
Page 14: Relay Controlled Outputs
Connect RS-485 cable to X1+, X1- and GND. Controllers are linked together through their RS-485 connectors. The maximum communication loop length is 1.2 kilometers (4,000 feet) using appropriate cabling. Connecting several KT-315 controllers at a single point is not acceptable nor are splitters or “spider web networks.”... -
Page 15: Connecting The Master Controller To The Host Pc
Over Corporate Network (LAN) If the master controller is used in a LAN-enabled corporate setting, use TCP/IP-to-RS-232 converter (such as the Kantech IP Link or the Lantronix UDS-1100 communication interface) to connect the controller to the corporate network. This method uses existing wiring for data exchange between EntraPass and the controllers. -
Page 16: Powering The Kt-315
Introduction to Combus Modules The Combus terminals on the KT-315 Controller are used to connect expansion modules to add inputs, outputs, relays and LCD time and date display. The four Combus terminals of the main panel must be connected to the four Combus terminals or wires of all modules. -
Page 17: Combus Specifications
Do not use any power supply other than the KT-PC4204 to repower the Combus. In the event of a power surge or transient, a module may lock up and cease to communicate with the controller. If the KT-315 loses communication with the module, it will initiate a module reset and will power down the Combus for five seconds in an attempt to reset the problem module. -
Page 18: Module Housing Cabinet
One (1) installation instructions sheet. Mounting the KT-PC4108 Module The KT-PC4108 module should be located inside a compatible cabinet (Kantech part no. KT-4051CAB), mounted in a dry, secure location. Preferably, it should be placed at a convenient distance from the connected devices. -
Page 19: Applying Power
1. Connect the four Combus wires to the KT-PC4108. Connect the Red, Black, Yellow and Green Combus wires to the RED, BLK, YEL and GRN terminals, respectively. 2. Complete all zone wiring to the zone input terminals (Z1-Z8). 3. Connect the external tamper switch, if used. NOTE: Consult the wiring diagram above for further information. -
Page 20: Kt-Pc4204 - 4-Relay And Additional Power Supply Module
Wiring may take place once the unit is mounted. Installation and Wiring Before wiring the unit, ensure that all power (AC transformer and battery) is disconnected from the KT-315 controller. Perform the following steps to complete wiring: 1. Connect the four Combus wires to the KT-PC4204. Connect the red, black, yellow and green Combus wires to the RED, BLK, YEL and GRN terminal respectively. -
Page 21: Applying Power
Applying Power After wiring is completed, apply power to the KT-315. Connect the battery leads to the battery, and connect the AC transformer. Then, connect power to the KT-PC4204; the battery leads followed by the AC transformer. NOTE: Do not connect the power until all wiring is complete. -
Page 22: Kt-Pc4216 - 16-Zone Output Expansion Module
Combus (since Combus can handle a maximum of 500 mA, a KT- PC4204 module in “repower” mode can be used to increase the current of the Combus of 1A). • Connects to KT-315 via 4-wire Combus • Nominal current draw of 15 mA •... -
Page 23: Applying Power
Applying Power 1. After all wiring is completed, apply power to the KT-315. 2. Connect the battery leads to the battery. 3. Then, connect the AC transformer. NOTE: Do not connect the power until all wiring is completed. Assigning the KT-PC4216 Module Follow the Instructions below for assigning and programming your KT-PC4216 module. -
Page 24: Troubleshooting Communication Problems
The KT-315 was communicating via the RS-232 port and you installed a VC-485 to communicate via the RS-485 port; c You were using the KT-315 at a local site and now want to configure it for remote operation. How to Use the Default Initialization (Hard Reset) 1. -
Page 25: Visual Status Indicators (Leds)
Visual Status Indicators (LEDs) The KT-315 controller has multiple status indicators such as for troubleshooting, network activity, power status and outputs activity. Please refer to the graphic below for a detailed view of their location. • HEARTBEAT (BLUE): This LED indicates the working status of KT-315. -
Page 26: Kt-315 Controller Maintenance Recommendations
Kantech. Do not crush, puncture, open, disassemble or otherwise mechanically interfere with the battery. Do not try to recharge the battery. If you need to dispose of the circuit board and/or the lithium battery, wrap the KT-315 in non-conductive tape. Check with your local authorities for battery disposal regulations. -
Page 27: Kt-315 Wiring Diagram
KT-315 Wiring Diagram... - Page 28 © 2018 Tyco Security Products. All rights reserved. www.kantech.com...