Related Manuals for Vista VP-HDA20-SM
Summary of Contents for Vista VP-HDA20-SM
- Page 1 Installation Manual VP-HDA20-SM Please read this manual thoroughly before use and keep it handy for future reference.
- Page 3 Norbain SD, 210 Wharfedale Road, Winnersh Triangle, Wokingham, Berkshire RG41 5TP, England. UK +44 (0) 118 912 5000 / Vista Technical Support +44 (0) 118 912 5125 Note: You should be at the equipment and ready with details before calling Technical Support.
- Page 4 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings.
-
Page 5: Table Of Contents
Table of Contents Chapter 1 — Introduction ....................6 1.1 Features ..........................6 Chapter 2 — Installation and Configuration ..............7 2.1 Package Contents ....................... 7 2.2 Mounting the Camera ......................8 2.2.1 Locking the Camera ...................... 8 2.3 Basic Configuration of Dome Camera System ..............10 2.4 Setting Dome Camera Address (ID) ................. -
Page 6: Chapter 1 - Introduction
Up to 3999 selectable camera addresses Function Run menu using DVR without function key (Pattern, Scan …) Hikvision-C, Pelco-C or Fastrax-C coaxial protocols Auto sensing RS485 telemetry supporting: Vista-485, Pelco P & D protocols 12VDC or 24VAC operation IP66 and built to IK10 (EN 62262) -
Page 7: Chapter 2 - Installation And Configuration
Chapter 2 — Installation and Configuration 2.1 Package Contents The cameras are housed in compact housing, constructed of aluminum, steel and plastic, designed for wall, ceiling and pole mounting. Bracketry is not included, so please discuss with sales regarding mounting options and bracketry required to fulfill this. The housing meets the Protection Classification IP66 standards for dust and moisture ingress. -
Page 8: Mounting The Camera
The dome cameras mounting bracket should be attached to a structural object, such as hard wood, wall stud or ceiling rafter that supports the weight of the dome camera. Please see the Vista Solution guide for available bracketry and mounting options. CAUTION: A silicone rubber sealant must be applied to seal the housing to secure waterproofing. - Page 9 CAUTION: Before installing mounting bracket to surface pre-adjust the four mounting screws "A" on the base of the dome camera to best match the mounting bracket locked position. Unscrew the locking screw on the side of the dome's base and fit the tab of the mounting bracket into the locking slot.
-
Page 10: Basic Configuration Of Dome Camera System
2.3 Basic Configuration of Dome Camera System Connector Wire Color Description 24VAC or 12VDC+ 3-pin terminal block WHITE 24VAC or 12VDC- GREEN RS-485+ 2-pin terminal block BLUE RS-485- GRAY ALARM INPUT 1 VIOLET ALARM INPUT 2 5-pin terminal block ORANGE ALARM INPUT 3 SKY BLUE ALARM INPUT 4... -
Page 11: Setting Dome Camera Address (Id)
Open the DIP switch cover and change the setting of DIP switch, replace this cover plate, taking care that it is seated and fitted correctly. NOTE: The cover plate is a primary seal, so failure to fit or refit it correctly will remove the IP66 protection and damage will occur to the camera not covered by the warranty. -
Page 13: Connections
2.6 Connections • Connecting to the RS-485 The dome camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex serial communications signals. • Connecting HD-TVI/AHD Output connector Connect the HD-TVI/AHD output (BNC) connector to the monitor or video input. •... -
Page 14: Getting Started
2.7 Getting Started Once installed apply power to the dome camera. The dome camera will start a configuration sequence. STATUS of FUNCTION TITLE AF AE FOCUS and AE INFORMATION EMPTY DATA DISPLAY ALARM:1 ALARM DISPLAY CAMERA TITLE & ID DOMEID:0001 360.0 090.0 PAN &... -
Page 15: Chapter 3 - Program And Operation
No. + CAM keys from your controlling device (keyboard/DVR). Example: Pressing 1 & CAMERA keys from a Vista VKBD4 keyboard sequentially, will select camera 1. The selected dome camera ID will be displayed on the LCD display of the keyboard controller. -
Page 16: Auto Scan Setup
3.4 Auto Scan Setup Allows the camera to be set up to move automatically between 2 programmed locations, the Auto Scan can be recalled from the controlling device using the AUX6 command from a VKBD4. AUTO SCAN SETUP NUMBER : 01 TITLE : A01 MODE... - Page 17 2. Select ‘MODE’ - adjust with (Tele/Wide) 3. Select ‘SPEED’ - adjust with (Tele/Wide) 4. ‘START ANGLE’ Use the Joystick to move cursor to START ANGLE Press the (IO/FN) key ‘CONTROL’ is displayed. Move the camera to the desired location and the zoom position. Press the (IC/FF) and ‘CONTROL’...
-
Page 18: Preset Setup
3.5 Preset Setup Up to 240 Presets may be programmed. Presets can be recalled No. + PRESET. Presets are very powerful and allow you to set the camera parameters and even a motion alarm for each preset. There are eight pages of Preset menu. Each page has 30 Presets. The pages can be scrolled by moving the Joystick to the NEXT PAGE and (Tele/Wide). - Page 19 Select ‘MOTION SETUP’ and move Joystick to the right, the ‘MOTION SETUP’ menu is displayed. MOTION SETUP SENSITIVITY: 10 RESOLUTION : 02 POSITION : ALL DELAY : 00 SEC OUTPUT : OFF HOLD TIME : 03 SEC EXIT(ESC TO EXIT) 00 –...
- Page 20 NOTE: AUTO in D/N MODE option is not applied in ‘MANUAL’ mode of AE Setup. Select ‘ADDITIONAL AE’ and move Joystick to the right, the ‘ADDITIONAL AE SETUP’ menu is displayed. ADDITIONAL AE SETUP : OFF : OFF WDR WEIGHT : -- : OFF : OFF...
-
Page 21: Quick Setting A Preset
3.6 Quick Setting a Preset This can be achieved after selecting the desired scene e.g. with VKBD4 by pressing FUNCTION (Fn) then the No. (1 to 240) then PRESET key sequentially. The current view will be stored to the selected Preset number. If the Preset number is not empty, an ‘OVER WRITE’... - Page 22 3. To scroll to a stored Preset, adjust with (Tele/Wide) then the stored Preset number displays. 4. To select functions other than Preset, press the (IO/FN) key to scroll for Tour, Pattern or Auto Scan respectively (if you wish to remove a Preset or Function from a Tour keep pushing (IO/FN) until ‘---‘...
-
Page 23: Pattern Setup (Learn Tour)
3.8 Pattern Setup (Learn Tour) The Pattern feature records up to a maximum of 500 seconds of user control. Up to 8 Patterns can be stored, inserted into a Tour and played back by pressing the No. + Learn keys sequentially. PATTERN SETUP (CTRL KEY) TITLE... -
Page 24: Privacy Zone Setup
3.9 Privacy Zone Setup Up to 16 Privacy Zones may be programmed. There are four pages of Privacy Zones menu. Each page has 4 Privacy Zones. The pages can be scrolled by moving the Joystick to the NEXT PAGE and (Tele/Wide). PRIVACY ZONE SETUP (CTRL KEY) METHOD... -
Page 25: Camera Setup
3.10 Camera Setup Use the Joystick to move the cursor, right to select sub menu (if applicable) and (Tele/Wide) to adjust. To save changes highlight ‘SAVE AND EXIT’ and move Joystick right. Joystick left exits without saving. CAMERA SETUP FOCUS CONTROL WB CONTROL AE CONTROL CAMERA CONTROL... - Page 26 • WB SETUP (White Balance) WB SETUP MODE : AUTO R GAIN : --- B GAIN : --- SAVE AND EXIT(ESC TO CANCEL) MODE AUTO, MANUAL, INCANDESCENT, FLUORESCENT, OUTDOOR Automatically computes the picture’s white balance using colour AUTO information from the entire screen. INCANDESCENT Incandescent white balance mode FLUORESCENT...
- Page 27 Permanent monochrome mode COLOUR Permanent colour mode These 3 settings can be temporarily overridden for a 60 second period via the day/night command function from the VKBD4. NOTE: AUTO in D/N MODE option is not applied in ‘MANUAL’ mode of AE Setup. ADDITIONAL AE SETUP ADDITIONAL AE SETUP : OFF...
-
Page 28: Dome Communication
: AUTO BAUDRATE : 9600 PARITY : NONE TERMINATION : OFF SAVE AND EXIT(ESC TO CANCEL) 1 – 3999 DOME ID PROTOCOL AUTO, F2/F2E, PELCO-PD, VISTA BAUDRATE 2400, 4800, 9600, 19200, 38400 bps PARITY NONE, EVEN, ODD TERMINATION (RS-485) OFF, ON... -
Page 29: Alarm Setup
3.12 Alarm Setup Use the Joystick to move the cursor and (Tele/Wide) to adjust. To save changes highlight ‘SAVE AND EXIT’ and move Joystick right. Joystick left exits without saving. ALARM SETUP (CTRL KEY) NO PRI FUN IN LATCH 001 NO OUT1 01 --- OFF --- OFF... -
Page 30: Configuration Menu (Dome Setup)
3.13 Configuration Menu (Dome Setup) Use the Joystick to move the cursor, right to select sub menu (if applicable) and (Tele/Wide) to adjust. To save changes highlight ‘SAVE AND EXIT’ and move Joystick right. Joystick left exits without saving. CONFIGURATION MENU HOME FUNCTION SETUP VIEW ANGLE SETUP ORIGIN OFFSET... - Page 31 • VIEW ANGLE SETUP Use the Joystick to move the cursor and (Tele/Wide) to adjust. To save changes highlight ‘SAVE AND EXIT’ and move Joystick right. Joystick left exits without saving. VIEW ANGLE SETUP PANNING RANGE FLIP : 90 TILT ANGLE LIMIT : 07 SAVE AND EXIT(ESC TO CANCEL) FLIP...
- Page 32 • OFFSET SETUP (Origin Offset) Use the Joystick to move the cursor and (Tele/Wide) to adjust. To save changes highlight ‘SAVE AND EXIT’ and move Joystick right. Joystick left exits without saving. OFFSET SETUP (CTRL KEY) PAN OFFSET : 000.0 TILT OFFSET : 000.0 ENABLE...
- Page 33 • OSD DISPLAY SETUP Use the Joystick to move the cursor, right to select sub menu (if applicable) and (Tele/Wide) to adjust. To save changes highlight ‘SAVE AND EXIT’ and move Joystick right. Joystick left exits without saving. OSD DISPLAY SETUP LANQUAGE : ENGLISH TITLE...
- Page 34 MOTOR SETUP Use the Joystick to move the cursor and (Tele/Wide) to adjust. To save changes highlight ‘SAVE AND EXIT’ and move Joystick right. Joystick left exits without saving. MOTOR SETUP PROPORTIONAL P/T P/T MODE : NORMAL SLOW PAN MAX SLOW TILT MAX NORMAL PAN MAX NORMAL TILT MAX...
- Page 35 ORIGIN CHECK If the presets or privacy zones appear to have moved, carry out an origin check as this will be zero the camera module position. Use the Joystick to move the cursor and right or (IO/FN) to accept selection. ORIGIN CHECK ARE YOU SURE ? CANCEL...
- Page 36 Cont/… ALARM OUT SETUP OUT1 : ALARM OUT2 : 1 MIN EXIT(ESC TO EXIT) (IO/FN) to operate alarm out during the setting time only. • SYSTEM INFORMATION SYSTEM INFORMATION CAMERA TYPE : xxxx-Vx.xx H/W VERSION : Vx.xx-xxxx ROM VERSION : Vx.xxxxxx PROTOCOL : xxxx BAUDRATE...
-
Page 37: Appendix A - Specifications
Appendix A — Specifications VP-HDA20-SM IMAGE Lens 4.7mm ~ 94.0mm (F1.6 – 3.0) Angle of View 55.5° (H) ~ 3.0° (H) Type 1/2.8" SONY STARVIS CMOS sensor Image Sensor Pixels 1945 (H) x 1097 (V) Color : 0.35 Lux @ 50IRE Min. - Page 38 Operating Humidity 0 ~ 90%RH (Non-condensing) Operating Temperature -10 C ~ 50 C Power Supply 12VDC, 24VAC Power Consumption 1.0A (12.0W) @ 12VDC, 24VAC Dimensions See dimension drawing Net Weight Approx. 1.6kg Ingress Protection IP66 Vandal Resistance IK10 (BS EN 62262) * Specifications are subject to change without notice * Figure –...
-
Page 39: Appendix B - Troubleshooting
Appendix B — Troubleshooting If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information. Problem Possible Solution Verify that power is connected to all pieces of equipment... - Page 41 Vista 210 Wharfedale Road Winnersh Triangle Wokingham Berkshire. RG41 5TP (Subject to change without notice) Version 1.1 50304027A...