How To Replace The Vacuum Belt And The Headlight Bulb - Titan T3200 Owner's Manual

HOW TO REPLACE THE VACUUM BELT AND
HEADLIGHT BULB
CAUTION: Unplug the vacuum cleaner�
How to Remove the Bottom Plate
1� Place the vacuum in the lowest position by stepping
on the handle release pedal (see "How to Adjust the
Handle" on page 5)� Turn the vacuum over on a flat
surface, exposing the bottom plate�
2� Remove the five screws holding the bottom plate in
place (Fig� 1)�
3� Remove the bottom plate�
How to Replace the Belt
1� Turn the vacuum over and remove the bottom plate
as described above�
2� Lift out the brushroll and remove the belt (Fig� 2)�
3� Loop a new belt around the drive shaft (Fig� 3)
and the raised ring between the bristles on the
brushroll (Fig� 4)�
4� Pull the brushroll forward (against the pull of the
belt) and reinsert the ends back into the nozzle
(Fig� 5) making sure to line up the end opposite the
belt so the flat edges slide down properly�
5� Turn the brushroll by hand, making sure the belt is
not twisted and all rotating parts move smoothly�
6� Replace the bottom plate and the five screws�
How to Replace the Bulb
1� Place the vacuum in the lowest position by stepping
on the handle release pedal (see "How to Adjust the
Handle" on page 5)�
2� Remove the two screws from the headlight lens (Fig� 6)�
3� Remove the lens and replace the bulb (Fig� 7)�
4� Replace the headlight lens and the two screws�
8
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 7
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 7
Maintenance -
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 7
Changing the Belt
Maintenance -
If the brush bar stops rotating, it is likely that the
Changing the Belt
drive belt has snapped (usually because the
brush has been stalled). Replacement belts can
Maintenance -
be obtained from Morphy Richards by calling the
If the brush bar stops rotating, it is likely that the
Changing the Belt
spare parts helpline number: 0844 873 0726.
drive belt has snapped (usually because the
brush has been stalled). Replacement belts can
Accessing the floor nozzle
If the brush bar stops rotating, it is likely that the
be obtained from Morphy Richards by calling the
Press the power pedal (26) to turn the cleaner off. drive belt has snapped (usually because the
1.
spare parts helpline number: 0844 873 0726.
brush has been stalled). Replacement belts can
Disconnect the cleaner from the mains supply.
2.
Accessing the floor nozzle
be obtained from Morphy Richards by calling the
Press the upright release pedal (18) and place the
spare parts helpline number: 0844 873 0726.
3. Press the power pedal (26) to turn the cleaner off.
1.
cleaner face down, in a flat position on a soft
Accessing the floor nozzle Disconnect the cleaner from the mains supply.
2.
surface (eg. carpet).
Press the power pedal (26) to turn the cleaner off.
1. Press the upright release pedal (18) and place the
3.
Removing brush bar and belt
cleaner face down, in a flat position on a soft
Disconnect the cleaner from the mains supply.
2.
Using a cross-headed screwdriver, unscrew the 5 surface (eg. carpet).
.
4
Press the upright release pedal (18) and place the
3.
screws on the base of the cleaner to release the
cleaner face down, in a flat position on a soft Removing brush bar and belt
L-shaped plate from over the rotary brush bar.
surface (eg. carpet).
Using a cross-headed screwdriver, unscrew the 5
.
4
screws on the base of the cleaner to release the
Removing brush bar and belt
L-shaped plate from over the rotary brush bar.
Using a cross-headed screwdriver, unscrew the 5
.
4
screws on the base of the cleaner to release the
Screw
L-shaped plate from over the rotary brush bar.
points
Screw
points
Screw
points
Remove the broken belt and lift out the rotary
5.
brush bar.
Remove the broken belt and lift out the rotary
5.
brush bar.
Remove the broken belt and lift out the rotary
5.
brush bar.
2.
3.
4
5.
Fig� 6
Disconnect the cleaner from the mains supply.
cleaner face down, in a flat position on a soft
Press the upright release pedal (18) and place the surface (eg. carpet).
cleaner face down, in a flat position on a soft
Removing brush bar and belt
surface (eg. carpet).
Using a cross-headed screwdriver, unscrew the 5
4 .
Removing brush bar and belt
screws on the base of the cleaner to release the
Using a cross-headed screwdriver, unscrew the 5 L-shaped plate from over the rotary brush bar.
.
screws on the base of the cleaner to release the
L-shaped plate from over the rotary brush bar.
Screw
points
Screw
points
Remove the broken belt and lift out the rotary
5.
Fig� 1
brush bar.
Remove the broken belt and lift out the rotary
brush bar.
Refitting brush bar and belt
Hook the belt over the drive shaft (the belt must
6.
be slid sideways past the end of the drive shaft).
Refitting brush bar and belt
Hook the belt over the drive shaft (the belt must
6.
be slid sideways past the end of the drive shaft).
Refitting brush bar and belt
Hook the belt over the drive shaft (the belt must
6.
Fig� 2
be slid sideways past the end of the drive shaft).
Drive
shaft
Drive
Pass the rotary brush bar through the belt,
7.
shaft
ensuring the correct end is located against the
belt.
Drive
Pass the rotary brush bar through the belt,
7.
shaft
ensuring the correct end is located against the
Fig� 3
belt.
Pass the rotary brush bar through the belt,
7.
ensuring the correct end is located against the
belt.
Pull the rotary brush bar forward (against the pull
8.
of the belt) and locate the square ends of the
brush bar into location slots in the floor nozzle.
Fig� 4
Pull the rotary brush bar forward (against the pull
8.
of the belt) and locate the square ends of the
brush bar into location slots in the floor nozzle.
Pull the rotary brush bar forward (against the pull
8.
of the belt) and locate the square ends of the
brush bar into location slots in the floor nozzle.
Fig� 5
Rotate the brush bar by hand to ensure the belt is
9.
running in the centre of its location on the brush.
Refitting the floor nozzle base cover
Rotate the brush bar by hand to ensure the belt is
9.
Refit the L-shaped plate over the rotary brush bar,
10 .
running in the centre of its location on the brush.
and screw the 5 screws back into the base of the
Refitting the floor nozzle base cover
Rotate the brush bar by hand to ensure the belt is
cleaner, using a cross-headed screwdriver, do not
9.
overtighten the screws. running in the centre of its location on the brush.
Refit the L-shaped plate over the rotary brush bar,
.
10
and screw the 5 screws back into the base of the
Return the cleaner to the upright position.
Refitting the floor nozzle base cover
11.
cleaner, using a cross-headed screwdriver, do not
Connect to the mains supply. Switch on to test.
Refit the L-shaped plate over the rotary brush bar,
.
10
overtighten the screws.
and screw the 5 screws back into the base of the
Return the cleaner to the upright position.
11. Fig� 7
cleaner, using a cross-headed screwdriver, do not
Connect to the mains supply. Switch on to test.
overtighten the screws.
Return the cleaner to the upright position.
11.
Connect to the mains supply. Switch on to test.
Pa
7.
en
Pa be
7.
en
be
Pu
8.
of
Pu br
8.
of
bru
Ro
9.
ru
Ro
9.
R
run
Re
.
10
Re
an
Re cl
.
10
ov
an
cle
Re
11.
ove
C
Re
11.
Co
7
7
7
7