superbrightleds ALKW9-RGB93 Instructional Sheet

Important: Read all instructions prior to installation.
Multi Color 9 Piece Accent Light Kit
Parts Included
3 - 10.7" Waterproof Accent Light Strips
2 - 8.8" Waterproof Accent Light Strips
4 - 4.8" Waterproof Accent Light Strips
1 - RF RGB Accent Light Controller
1 - RF Wireless Key Chain Remote
Installation
1. Connect strips to the connection box then connect to the Adapter Cable
with the "To Splitter" arrow towards the Connection Box. Connect the other
end of the Adapter Cable with the "To Controller" arrow towards the Controller.
Temporarily apply power to the controller and test strip locations for proper
lighting effect.
2. Mark the desired location of the strips. Mount strips using double sided tape
or silicone in desired location and away from heat sources and moving parts.
3. Mount controller and connection box in dry locations away from heat sources
and moving parts and route power wires to power source then connect. Route
white antenna wire away from metal objects for maximum operating range.
Specifications
Input Voltage
Controller Output Current
Fuse Size
Operating Temperature
Strip IP Rating
Static Color Dynamic Modes
Seven Color Dynamic Modes
Static Colors
Override Mode
Brightness Levels
Remote Battery
Remote Range
Remote Frequency
FCC ID
Warranty
Wiring
Input Wires Polarity
Black Negative (-)
Red Positive (+)
Blue (see below) Positive (+)
Blue wire activates red single color mode at full brightness while voltage is applied.
Use for brake override if required. Works as brake override even when controller is
Output Connector Polarity
Black Positive (+)
Red Negative (-)
Green Negative (-)
Blue Negative (-)
Remote Pairing
Remote comes paired to the controller. Use the following procedure if additional
remotes are required.On power up, LEDs will be green indicating pairing mode
for three seconds. During green pairing mode, press button "A" then "B" to pair a
new remote.
4400 Earth City Expy, St. Louis MO 63045
1 - Connection Box
1 - Adapter Cable (LC4 to LC4)
9 - Adapter Cables (LC4 to 4pin)
1 -12V 27A Battery
9~14.5 VDC
3 x 1A Maximum
3A
-4 ~149° F (-20~65° C)
Waterproof IP68
2
2
18
1
5
12V 27A x 1
33 Feet (10m) Maximum
315 MHz
2AFXS-JX-R001
2 Years
Purpose
Ground In (-)
9~14.5 VDC Power In (+)
9~14.5 VDC Red Override Signal In (+)
in standby mode.
Purpose
Common Anode
Red LED Cathode
Green LED Cathode
Blue LED Cathode
Instructional Sheet
Part Number:
ALKW9-RGB93
Diagram 1
Adapter Cables
Connection Box
1/4" Snap Spades
Power Supply Battery
(CPS-12VDC-50W)
OR
CPS connector
(CPS-F2ST)
Remote Functions
Button
Cycles up through 18 single color modes and two 7 color modes.
Press and hold for dimming 80%, 60%, 40%, 20% and back to
100% during single color modes.
Activates Flash Modes during single color modes. Switches
between Flash/Flash/Long Pause and Flash/Flash/Short Pause
during flash modes. Increases cycle speed during 7 color modes
Activates Fading Mode during single color modes. Decreases
cycle speed during 7 color modes.
Hold for 6 seconds to return to Mode 1 (Static Red)
Remote Battery Replacement
1. Remove three philips head screws and remove the button panel.
2. Carefully remove battery and replace with new.
3. Reposition button panel then insert and tighten screws
Ground
866-590-3533
PSC-164
Running Light Cicuit (+)
Brake Light
Circuit (+)
RCW-RFRGB
White
Antenna
To Brake
Switch
Blue
Brake
Override
To Splitter To Controller
Adapter Cable
Functions
On/Off
RCW-RFR
support@superbrightleds.com
RCW-RFRGB
RF Controller