superbrightleds ALKW5-RGB45 Instructional Sheet

Important: Read all instructions prior to installation.
Multi Color 5 Piece Accent Light Kit

Parts Included

5 - 5" Weatherproof Accent Light Strips
1 - RF RGB Accent Light Controller (RCW-RFRGB)
1 - RF Wireless Keychain Remote (RCW-RFR)
1 - Adapter Cable (LC4 to LC4)
1 - Splitter Cable
1 - 12V 27A Battery

Installation

1. Connect strips to the connection box then connect to the Adapter Cable with
the "To Splitter" arrow towards the Splitter Cable. Connect the other end of the
Adaptor Cable with the "To Controller" arrow towards the Controller. Temporarily
apply power to the controller and test strip locations for proper lighting effect.
2. Mark the desired location of the strips. Mount strips using double sided tape
or silicone in desired location and away from heat sources and moving parts.
3. Mount controller in a dry location away from heat sources and moving parts
and route power wires to power source then connect. Route white antenna wire
away from metal objects for maximum operating range.

Specifications

Input Voltage
Controller Output Current
Fuse Size
Operating Temperature
Strip IP Rating
Static Color Dynamic Modes
Seven Color Dynamic Modes
Static Colors
Override Mode
Brightness Levels
Remote Battery
Remote Range
Remote Frequency
FCC ID
Warranty

Wiring

Input Wires Polarity
Black Negative (-)
Red Positive (+)
Blue (see below) Positive (+)
Blue wire activates red single color mode at full brightness while voltage is applied.
Use for brake override if required. Works as brake override even when controller is
in standby mode.
Output Connector Polarity
Black Positive (+)
Red Negative (-)
Green Negative (-)
Blue Negative (-)

Remote Pairing

Remote comes paired to the controller. Use the following procedure if additional
remotes are required.On power up, LEDs will be green indicating pairing mode
for three seconds. During green pairing mode, press button "A" then "B" to pair a
new remote.
4400 Earth City Expy, St. Louis MO 63045
9~14.5 VDC
3 x 1A Maximum
3A
-4 ~149° F (-20~65° C)
Weatherproof IP65
2
2
18
1
5
12V 27A x 1
33 Feet (10m) Maximum
315 MHz
2AFXS-JX-R001
2 Years
Purpose
Ground In (-)
9~14.5 VDC Power In (+)
9~14.5 VDC Red Override Signal In (+)
Purpose
Common Anode
Red LED Cathode
Green LED Cathode
Blue LED Cathode
Instructional Sheet
Part Number:
ALKW5-RGB45
Diagram 1
5-way
Splitter
1/4" Snap Spades
Power Supply
Battery
(CPS-12VDC-50W)
OR
CPS connector
(CPS-F2ST)

Remote Buttons

Button Functions
Cycles up through 18 single color modes and two 7 color modes.
Press and hold for dimming 80%, 60%, 40%, 20% and back to
100% during single color modes.
Activates Flash Modes during single color modes. Switches
between Flash/Flash/Long Pause and Flash/Flash/Short Pause
during flash modes. Increases cycle speed during 7 color modes
Activates Fading Mode during single color modes. Decreases
cycle speed during 7 color modes.
On/Off
Hold for 6 seconds to return to Mode 1 (Static Red)
Remote Battery Replacement
1. Remove three philips head screws and remove the button panel.
2. Carefully remove battery and replace with new.
3. Reposition button panel then insert and tighten screws
866-590-3533 support@superbrightleds.com
Ground
White
Antenna
RCW-RFRGB
RF Controller
To Brake
Switch
Blue
Brake
Override
To Splitter To Controller
Adapter Cable
Black Ground
RCW-RFR