Yamaha AN1x Owner's Manual page 75

So ur ce
The So urce setting determines which co ntro ller (by
Co ntro l Chang e number) is assig ned to co ntro l the
co rrespo nding Parameter.
You can set the source by Control Change number or by controller name, as
shown in the Settings listed below.
Settings:
CcO ff:
N o co ntro ller assig ned.
CC1 ~ 9 5 : Selects the So urce co ntro ller acco rding to Co ntro l
Chang e number, when received by o n-bo ard co ntro llers o r
inco ming MIDI messag es.
AT (After Touch):
Fo r co ntro lling with keybo ard After T o uch.
PB (Pitch Bend):
Fo r co ntro lling with the Pitch Bend wheel.
KyTrk (Key Tra ck ): Fo r co ntro lling with no te number
messag es g enerated by pressing the keys.
Vel (Velocity):
Fo r co ntro lling with keybo ard velo city, o r the
streng th with which yo u strike the keys.
KyRnd (Key Ra ndom ):
Fo r co ntro lling with rando m no te
number messag es g enerated by pressing the keys.
A.M W (Assign M odula tion W heel):
the Mo dulatio n W heel, and/ o r by inco ming MIDI messag es
with the same Co ntro l Chang e number as assig ned to the
MW .
A.FV (Assign Foot Volume):
co nnected Fo o t Vo lume co ntro ller, and/ o r by inco ming MIDI
messag es with the same Co ntro l Chang e number as assig ned
to the FV.
A.FC (Assign Foot Control): Fo r co ntro lling with a
co nnected fo o t co ntro ller, and/ o r by inco ming MIDI messag es
with the same Co ntro l Chang e number as assig ned to the FC.
A.FS (Assign Footsw itch):
Fo r co ntro lling with a
co nnected Fo o tswitch, and/ o r by inco ming MIDI messag es
with the same Co ntro l Chang e number as assig ned to the FS.
A.RbX (Assign Ribbon Controller-X ):
with the Ribbo n co ntro ller X-axis (left and rig ht), and/ o r by
inco ming MIDI messag es with the same Co ntro l Chang e
number as assig ned to the RbX.
A.RbZ (Assign Ribbon Controller-Z):
with the Ribbo n co ntro ller Z-axis (push), and/ o r by inco ming
MIDI messag es with the same Co ntro l Chang e number as
assig ned to the RbZ.
Kn1 ~ 8 (Knob 1 ~ 8 ): Fo r co ntro lling with a specified
CO N TRO L kno b (when KN O B PARAMETER G RO UP
[ASSIG N ] is o n).
Depending on selected Parameter, the available Source for assignment may be
different. For details of available parameters, see the table of Control Matrix
parameters in the separate Data List book.
Fo r co ntro lling with
Fo r co ntro lling with a
Fo r co ntro lling
Fo r co ntro lling
75
You cannot assign the same Source controller and Parameter to more than one
set. If you attempt to, lower-numbered sets will take priority, and " – – – " will
appear in the LCD for higher-numbered sets.
When you select [ RIBBON] controller " A.RbX" as the " Source" controller and Pitch
Up/ Pitch Down as the " Parameter" , the [ RIBBON] controller value will be reset to
the center position when you release your finger from the [ RIBBON] . The sets
with different Parameters ( other than Pitch Up/ Pitch Down) keep the position at
which you release your finger.
D e p t h
The Depth setting determines the co ntro l rang e o f the
So urce co ntro ller.
Settings:
Depending o n the selected Parameter, the available setting s
may be different. Fo r details, see the table o f Co ntro l Matrix
parameters in the separate Data L ist bo o k.
Direct Control Function
W hen Depth " Dirct" is selected (0 setting ), the Direct Co ntro l
functio n is activated, and yo u can directly edit the parameter
assig ned to the co ntro ller within its o rig inal rang e.
Rela tionship Betw een Control M a trix And
Utility Control Assign Function
There are two types o f Co ntro l Chang e assig nment
functio ns— the Co ntro l Matrix and the Utility Co ntro l Assig n
functio n. Between the Co ntro l Matrix and Utility Co ntro l
Assig n functio n (see pag e 9 5 ), yo u can co nfig ure a
so phisticated co ntro ller setup to co ntro l specific parameters o f
the internal to ne g enerato r and an external to ne g enerato r at
the same time by the eig ht CO N TRO L kno bs and o ther
co ntro llers. Co ntro l Chang e assig nments made in the Utility
Co ntro l Assig n functio n are sent to bo th MIDI [O UT] as well
as the Co ntro l Matrix, where it can be rero uted at will befo re
reaching the internal to ne g enerato r. External Co ntro l
Chang e sig nals received at MIDI [IN ] can be ro uted thro ug h
the Co ntro l Matrix to co ntro l the AN 1 x to ne g enerato r
parameter o f yo ur cho ice.
Control Signal Flow
AN1x Tone Generator
Control Matrix
Utility Control
Assign
MIDI IN
MIDI OUT