Yamaha AN1x Owner's Manual page 111

Cha nnel M ode M essa ges
The fo llo wing Channel Mo de Messag es can be received.
2nd BYTE 3rd BYTE MESSAGE
120 0
121 0
123 0
126 0 ~ 16
127 0
A ll So und s O f f ( Co nt r o l # 1 2 0 )
Clears all so unds currently so unding o n the specified
channel. Ho wever, the status o f channel messag es such
as N o te O n and Ho ld O n is maintained.
Re se t A ll Co nt r o lle r s ( Co nt r o l # 1 2 1 )
The values o f the fo llo wing co ntro llers will be reset to
the defaults: Pitch Bend, Channel Pressure, Sustain
Switch, Mo dulatio n, Expressio n, Po rtamento , RPN * ,
Vo lume, Pan, Effect Send L evel 1 , 3 , 4 .
* N umber no t specified; internal data will no t chang e.
A ll N o t e s O f f ( Co nt r o l # 1 2 3 )
Clears all no tes currently o n fo r the specified channel.
Ho wever, if Sustain Switch is o n, no tes will co ntinue
so unding until these are turned o ff.
M o no ( Co nt r o l # 1 2 6 )
Perfo rms the same functio n as when an All So unds O ff
messag e is received, and if the 3 rd byte (mo no
number) is in the rang e o f 0 - 1 6 , sets the
co rrespo nding channel to Mo no Mo de (Mo de 4 : m =
1 ).
Po ly ( Co nt r o l # 1 2 7 )
Perfo rms the same functio n as when an All So unds O ff
messag e is received, and sets the co rrespo nding
channel to Po ly Mo de (Mo de 3 ).
Progra m Cha nge
Messag es which select vo ices.
Cha nne l Afte r touch
Messag es which let yo u co ntro l the so unds by the pressure
yo u apply to the keys after the initial striking o f the keys,
o ver the entire channel.
Pitch Be nd
Pitch Bend messag es are co ntinuo us co ntro ller messag es
that allo w the pitch o f desig nated no tes to be raised o r
lo wered by a specified amo unt o ver a specified duratio n.
All Sounds Off
Reset All Controllers
All Notes Off
Mono
Poly
2 . SYSTEM M ESSAGES
System messag es are the data related to the o verall system
o f the device.
Syste m Ex clusiv e M e ssa ge s
System Exclusive messag es co ntro l vario us functio ns o f the
AN 1 x, including master vo lume and master tuning , effect
type and vario us o ther parameters.
M a st e r Vo lum e
W hen received, the Vo lume MSB will be effective fo r
the System Parameter.
F0 7 F 7 F 0 4 0 1 ll mm F7 (Hexadecimal)
* mm(MSB) = appro priate vo lume value, ll(L SB) =
ig no red
Activ e Se nsing
O nce FE (Active Sensing ) has been received, if no MIDI
data is subsequently received fo r lo ng er than an interval o f
appro ximately 3 0 0 msec, the AN 1 x will perfo rm the same
functio n as when All So unds O ff, All N o tes O ff, and Reset
All Co ntro llers messag es are received, and will then return
to a status in which FE is no t mo nito red.
Refer to the MIDI Data Fo rmat in the separate Data L ist
bo o k fo r mo re info rmatio n abo ut the vario us messag es.
Control Cha nge M odes
The AN 1 x has two Co ntro l Chang e mo des. Mo de 1
co rrespo nds to the list o f Co ntro l Chang e parameters
acco rding to the MIDI standard. Mo de 2 is a special list o f
Co ntro l Chang e parameters unique to the AN 1 x.
Fo r info rmatio n abo ut chang ing mo des, see pag e 9 6 . Fo r a
list o f Co ntro l Chang e parameters fo r each mo de, see the
separate Data L ist bo o k.
111