Related Manuals for Vanco Evolution EV4K2006
Summary of Contents for Vanco Evolution EV4K2006
- Page 1 HDMI® E X T E N D E R over single Cat5e/Cat6 Cable Vanco Part Number EV4K2006 4K HDMI® Extender over Single Category 5e/6 Cable with POE www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 FEATURES INTRODUCTION The Evolution by Vanco EV4K2006 HDMI Extender over Single Cat5e/6 with Bi-directional IR, auto EDID/EQ, and Bi-directional PoE extends 4K ultra high definition video with HDR and audio signals, IR, and power. Extends 4K@60Hz, 4:4:4 Chroma Subsampling and HDR up to 164ft/50m, and 4K@30Hz, 4:4:4 Chroma Subsampling, and HDR up to 130ft/40m. Bi- directional Power over Ethernet (PoE) Technology transmits power over Cat5e/6, allowing either the Transmitter or Receiver to be powered without the use of a power supply.
-
Page 4: Specifications
SPECIFICATIONS TECHNICAL SPECS HDMI Compliance ............HDMI Deep Color 30/36/48 bit color depth, Full 3D HDCP Compliance ............Yes Video Bandwidth ............594 MHz Video Support ............480i/480p/720p/1080i/1080p/4Kx2K @60 Audio Support ............Surround Sound (up to 7.1 ch) or stereo digital audio Input TMDS Signal ............. -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS Transmitting Unit Receiving Unit 12 13 1. HDMI INPUT: Connect a source such as a Blu-ray player, cable box, computer, NVR/DVR, etc. 2. IR TX – Plug in included IR Blaster to control the source (see IR section for setup and installation) 3. -
Page 6: Connection Diagram
CONNECTION DIAGRAM CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. 2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit. 3. - Page 7 IR PASS-THROUGH The bi-directional IR system allows you to control the source that is connected to the extender unit, from the display; or the display from the source. There are two important things to note when setting up the IR system: 1.
- Page 8 IR RECEIVER (RX) • To control the source: Plug IR Receiver into IR RX port of receiver unit (EV4K2006-RX); place receiver at or near display. • To control the display: Plug IR Receiver into IR RX port of transmitter unit (EV4K2006-TX); place receiver in position where it is able to receive remote signals.
- Page 9 NOTICE 1. Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.
-
Page 10: Troubleshooting
4. If you are still encountering issues, attempt the “hot-plug concept. With all of the HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. -
Page 11: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...