Related Manuals for Vanco EVOLUTION EV4K2004
Summary of Contents for Vanco EVOLUTION EV4K2004
- Page 1 HDMI® E X T E N D E R over Single Coax Cable with Bi-directional IR Vanco Part Number EV4K2004 4K HDMI® Extender over Single Coax Cable with Bi-directional IR www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
-
Page 3: Package Contents
INTRODUCTION The Evolution by Vanco EV4K2004 HDMI Extender can send and receive 4K resolutions over single RG6 coaxial cable with Bi- directional IR. Capable of extending 4K@60Hz up to a distance of up to 330ft/100m and 4K@60Hz with HDR10 High Dynamic Range up to 230ft/70m. -
Page 4: Specifications
SPECIFICATIONS TECHNICAL SPECS HDMI Compliance ............HDMI Deep Color 30/36/48 bit color depth, Full 3D HDCP Compliance ............Yes Video Bandwidth ............594 MHz Video Support ............480i/480p/720p/1080i/1080p/4Kx2K @60 Audio Support ............Surround Sound (up to 7.1 ch) or stereo digital audio Input TMDS Signal ............. - Page 5 Supported Resolutions 480i 60Hz 1080p 29.97 (30) Hz 4K2K 50Hz 4:2:0 480P 60Hz 1080p 50Hz 4K2K 50Hz 4:2:0 10/12bit** 576i 50Hz 1080p 59.94 (60) Hz 4K2K 50Hz 4:2:2 576P 50Hz 1080p 59.94 (60)Hz 10/12bit** 4K2K 50Hz 4:4:4 720P 50Hz 4K2K 24Hz 4:4:4 4K2K 60Hz 4:2:0 720P 59.94(60)Hz 4K2K 24Hz 4:4:4 10/12bit**...
-
Page 6: Panel Descriptions
PANEL DESCRIPTIONS Transmitting Unit 1. DC 5V: Connect included 5V DC power supply 2. POWER/SIGNAL LED: Blue LED - POWER; Green LED - SIGNAL ACTIVE 3. COAX OUT: Connect an RG6 coaxial cable using BNC connection 4. Micro-USB port: Reserved for available firmware updates; any firmware updates will be accessible on www.vanco1.com, on the product page under the “Downloads”... -
Page 7: Connection Diagram
CONNECTION DIAGRAM BluRay® Player IR Transmitter HDTV IR Transmitter IR Receiver HDMI IR Receiver HDMI Transmitter Receiver Front Front Back Back HDMI over Coax Cable CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the transmitting unit 2. -
Page 8: Ir Pass-Through
IR PASS-THROUGH IR Blaster TX IR Receiver RX IR BLASTER (TX) • To control the source: Plug IR Blaster into IR TX port of transmitter unit (EV4K2004-TX); place blaster in front of the IR eye of the source • To control the display: Plug IR Blaster into IR TX port of receiver unit (EV4K2004-RX); place blaster in front of the IR eye of the display IR RECEIVER (RX) •... - Page 9 NOTICE 1. Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.
-
Page 10: Troubleshooting
4. If you are still encountering issues, attempt the “hot-plug concept. With all of the HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. -
Page 11: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...