Mitsubishi MELSEC-A A2USHCPU-S1 User Manual page 218

APPENDICES
Number Name
*2 *3
I/O change flag
M9094
Duplex
M9095 operation verify
error
A3VCPU A
M9096
selfcheck error
A3VCPU B
M9097
selfcheck error
A3VCPU C
M9098
selfcheck error
A3VTU
M9099
selfcheck error
SFC program
M9100
registration
*2 SFC program
M9101 start/stop
*2 SFC program
M9102 starting status
*: Usable with AnN and AnA which are compatible with SFC.
For the AnN and AnA which are compatible with SFC, refer to the MELSAP-II Programming Manual.
Table App2.1 Special Relay List (Continue)
Description
• After the head address of the required I/O module
is set to D9094, switching M9094 on allows the I/O
module to be changed in online mode. (One
module is only allowed to be changed by one
setting.)
OFF:Changed • To be switched on in the program or peripheral
ON: Not changed device test mode to change the module during
CPU RUN. To be switched on in peripheral device
test mode to change the module during CPU
STOP.
• RUN/STOP mode must not be changed until I/O
module change is complete.
• During duplex operation of the operating CPU with
OFF:Normal
a stand-by CPU, verification is performed by the
ON: Duplex operation
both to each other. Turned on when a verify error
verify error
occurred.
OFF:No error • Turn on when a self-check error occurred on the
ON: Error A3VCPU A mounted next to the A3VTU.
OFF:No error • Turn on when a self-check error occurred on the
ON: Error A3VCPU B mounted next to the A3VCPU A.
OFF:No error • Turn on when a self-check error occurred on the
ON: Error A3VCPU C mounted next to the A3VCPU B.
OFF:No error • Turned on when a self-check error occurred on the
ON: Error A3VTU.
OFF:No SFC program
• Turned on if the SFC program is registered, and
ON: SFC program
turned off if it is not.
registered
• Should be turned on by the program if the SFC
OFF:SFC program stop program is to be started. If turned off, operation
ON: SFC program start output of the execution step is turned off and the
SFC program is stopped.
• Selects the starting step when the SFC program is
restarted using M9101.
ON:
OFF: All execution conditions when the SFC
OFF:Initial start
ON: Continuous start
• Once turned on, the program is latched in the
system and remains on even if the power is turned
off.
Should be turned off by the sequence program
when turning on the power, or when starting with
the initial step of block 0.
Details
Started with the step of the block being
executed when the program stopped.
program stopped are cleared, and the
program is started with the initial step of
block 0.
APP - 23
Applicable CPU
Usable with An,
—
AnN, AnA, AnU.
— Dedicated to A3V.
— Dedicated to A3V.
— Dedicated to A3V.
— Dedicated to A3V.
— Dedicated to A3V.
Usable with AnN* ,
AnA*, AnU,
A2AS, QCPU-A
— (A Mode), A2C,
A0J2H, AnS,
AnSH, A1FX and
A52G.
Usable with AnN*,
AnA*, AnU,
A2AS, QCPU-A
— (A Mode), A2C,
A0J2H, AnS,
AnSH, A1FX and
A52G.
Usable with AnN*,
AnA*, AnU,
A2AS, QCPU-A
— (A Mode), A2C,
A0J2H, AnS,
AnSH, A1FX and
A52G.