Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Homestyles Manuals
  4. Indoor Furnishing
  5. Storage Island 20 08000 0912
  6. Manual

Homestyles Storage Island 20 08000 0912 Manual

Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
IMPORTANT
Part List
E.
Middle Panel
1 pc.
F.
Front Rail
2 pcs.
Hardware List
Cam Lock
30 pcs. (+6 extra)
Cam Lock Screw
48 pcs. (+2 extra)
Carton 20 08000 0911 is also needed for assembly.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16" Drill Bit, 3/8" Drill Bit
20 08000 0912
Storage Island
G.
Plinth
2 pcs.
H.
Plinth
2 pcs.
I.
Shelf
3 pcs.
Cam Lock (small)
Plastic Cap
18 pcs. (+2 extra)
2 pcs. (+1 extra)
Dowel
Adjustable Pin
20 pcs. (+1 extra)
12 pcs. (+1 extra)
J.
Drawer
1 pc.
K.
Drawer
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
M3 x
.5 25
Wood Screw
15 pcs. (+1 extra)
M3 x
.5 64
Wood Screw (long)
M3 x
.5 38
14 pcs. (+1 extra)
Wood Screw for
Bottom
6 pcs. (+1 extra)

Advertisement

loading
Need help?

Need help?

Do you have a question about the Storage Island 20 08000 0912 and is the answer not in the manual?

Questions and answers

Related Manuals for Homestyles Storage Island 20 08000 0912

Summary of Contents for Homestyles Storage Island 20 08000 0912

  • Page 1 20 08000 0912 Storage Island IMPORTANT Part List Plinth Drawer 2 pcs. 1 pc. Middle Panel Plinth 1 pc. 2 pcs. Front Rail Shelf Drawer 2 pcs. 3 pcs. 2 pcs. Refer to later page(s) of these instructions for drawer assembly. Hardware List M3 x .5 25...
  • Page 2 Assembly Instructions 2/8 IMPORTANT Ÿ Use a soft cloth between these parts and the floor. Ÿ Do not use power tools above 8 volts to assemble. Ÿ Do not tighten all the bolts until each part is properly assembled. Ÿ The unit must be level to work properly.
  • Page 3 Assembly Instructions 3/8 Dowel Cam Lock STEP 3 Attach Side Panels (C) and (D) to Middle Panel (E) and Front Rails (F) with Dowels and Cam Locks. Wood Screw for Bottom Cam Lock Dowel STEP 4 Attach Bottom (B) to unit with Dowels, Cam Locks and Wood Screws for Bottom.
  • Page 4 Assembly Instructions 4/8 Wood Screw (long) STEP 5 Attach unit from Step 2 to unit from Step 4 with Dowels and Wood Screws (long) into pre-drilled holes. Dowel Figure 3 Plastic Cap Dowel Cam Lock STEP 6 Turn unit over to it’s upright position. Attach Top (A) to unit with Dowels and Cam Locks.

  • Page 5: Part List

    Assembly Instructions 5/8 Drawer (J) Wood Screw STEP 7 Attach Drawer Sides (J3) and (J4) to Drawer Back (J2) with Wood Screws. Wood Screw STEP 8 Slide Drawer Bottom (J5) into groove in unit. Attach Support (J6) to unit with Wood Screw.
  • Page 6 Assembly Instructions 6/8 Drawer (K) Wood Screw STEP 10 Attach Drawer Sides (J3) and (J4) to Drawer Back (J2) with Wood Screws. STEP 11 Wood Screw Slide Drawer Bottom (K5) into groove in unit. Attach Support (J6) to unit with Wood Screw.
  • Page 7 Assembly Instructions 7/8 STEP 13 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 4) Note: Unit must be level to work properly. Slide Drawers (J) and (K) into position. Figure 4 Figure 5 Adjustable Pin STEP 14 Insert Adjustable Pins into side panels at desired level.

  • Page 8: Hardware List

    Assembly Instructions 8/8 Per regulatory requirements, a Tip-over Restraint is included. Follow Step 15 to install it. STEP 15 Drill a 3/16” hole 1/2” deep 1” below top of unit in middle of side panel that is against a wall. Anchor in wall Wall Screw Bracket...
  • Page 9 CARE INSTRUCTIONS NEVER NEVER use glass cleaners on allow liquids to remain on furniture. finished furniture. Ammonia Absorption causes parts to warp chemically attacks the finish. and split and finishes to delaminate. Do not use power tools Do not place Do not write above 8 volts to assemble.