Page 1
Instructions for Use Leica HI1210 Water Bath Leica HI1210 V 3.4 , English 09/2018 Order No.: 14 0415 80101 RevI Always keep this manual with the instrument. Read carefully before working with the instrument.
Page 3
Leica reserves the right to change technical following thorough investigation in this field. specifications as well as manufacturing process- We are under no obligation to update the pres- es without prior notice.
Technical data ..........................9 Instrument Setup ......................10 Location conditions ........................10 Standard delivery ........................10 Unpacking and setting up the HI1210 ..................11 Setting up the power supply ..................... 11 Operation ........................12 Control panel fields on the instrument ..................12 Switching the instrument on .....................
Minimum 10 % r.H., Maximum 85 % r.H European directives. Indicates the item can be recycled Caution, consult the instructions for where correct facilities exist. use for cautionary information. Leica HI 1210 Water Bath...
EMC and EME. number is attached to the rear side of the instru- ment. Qualification of personnel • The Leica HI1210 may be operated by trained laboratory personnel only. • All laboratory personnel designated to operate this instrument must read these Instructions...
• Be sure to read these notes even if you are already familiar with the operation and use of other Leica products. • The protective devices located on the instrument and the accessories must not be removed or modified. Only qualified service personnel authorized by Leica may repair the instrument and access its internal components. Residual risks •...
To ensure trouble-free operation of the instrument, make sure to comply with the following instructions and warnings. Please note that electrostatic charge may result through direct or indirect contact with the Leica HI1210. Instructions for Use V 3.4 RevI – 09/2018...
Pollution degree: 2 Overvoltage category: II Operating temperature range: +15 °C to +40 °C Temperature control range: Room temperature to 75 °C Operating elevation: maximum of 2000 m above sea level IP protection class (IEC 60529): IP20 Leica HI 1210 Water Bath...
Check the delivery carefully against the packing list, delivery note and your order. Should you find any discrepancies, please contact your Leica sales office without delay. Instructions for Use V 3.4 RevI – 09/2018...
Instrument Setup Unpacking and setting up the HI1210 Set the carton on a flat surface, cut through the adhesive tape (Fig. 2) and open the carton (Fig. Fig. 3 Fig. 2 Remove the accessories and carefully lift the Hold the instrument firmly with one hand, pull off instrument out of the carton (Fig.
Operation Control panel fields on the instrument POWER LED Is illuminated when the instrument is switched on with the main power switch. Indicates the selected target tempera- ture. Set key: lower temperature. Set key: increase temperature. RUN/STOP Switch instrument on or off. 10 = Display Fig.
Switching off the instrument • The instrument can be switched off by pressing the RUN/STOP key. You do not have to switch the main power switch on or off each time for everyday routine use. Leica HI 1210 Water Bath...
Cleaning and Maintenance Cleaning the instrument • Before cleaning the instrument, turn off using the power switch (Fig. 6, 3) and disconnect from the power supply. • The instrument has a continuous front panel and no lateral cooling slots, so the surfaces are smooth and easy to clean.
Leica Biosystems Nussloch GmbH guarantees that the contractual prod- uct delivered has been subjected to a comprehensive quality control procedure based on the Leica in-house testing standards, and that the product is faultless and complies with all technical specifications and/ or characteristics warranted.
Decontamination Confirmation Every product that is returned to Leica Biosystems or that requires on-site maintenance must be properly cleaned and decontaminated. You can find the dedicated template of the decontamination confirmation on our website www.LeicaBiosystems.com within the product menu. This template has to be used for gathering all required data.
Need help?
Do you have a question about the HI1210 and is the answer not in the manual?
Questions and answers