Appendix 3 Instructions For Ul And Cul; Appendix 4 Instructions For - Mitsubishi Electric FR-F806-E Hardware Instruction Manual

Appendix 3
(Standard to comply with: UL 508C, CSA C22.2 No.274-13)
General precaution
CAUTION - Risk of Electric Shock -
The bus capacitor discharge time is 10 minutes. Before starting wiring or inspection, switch power off, wait for more than 10
minutes.
ATTENTION - Risque de choc électrique -
La durée de décharge du condensateur de bus est de 10 minutes. Avant de commencer le câblage ou l'inspection, mettez
l'appareil hors tension et attendez plus de 10 minutes.
Installation
The below types of inverter have been approved as products for a UL type12 enclosure that is suitable for Installation in a
Compartment Handling Conditioned Air (Plenum).
Install the inverter so that the ambient temperature, humidity and ambience of the inverter will satisfy the specifications. (Refer
to page 18.)
The drive must be installed in clean air according to enclosure classification.
Cooling air must be clean, free from corrosive materials and electrically conductive dust regarding the UL Type 12 enclosure.
This enclosure provides protection from airborne dust and light sprays or splashing water from all directions.
 Branch circuit protection
For installation in the United States, Class T, Class J, or Class CC fuse, or UL 489 Molded Case Circuit Breaker (MCCB)
must be provided, in accordance with the National Electrical Code and any applicable local codes.
For installation in Canada, Class T, Class J, or Class CC fuse, or UL 489 Molded Case Circuit Breaker (MCCB) must be
provided, in accordance with the Canadian Electrical Code and any applicable local codes.
FR-F846-[]
Rated fuse voltage (V)
Fuse allowable rating (A)
Molded case circuit breaker (MCCB)
Maximum allowable rating (A)
FR-F846-[]
Rated fuse voltage (V)
Fuse allowable rating (A)
Molded case circuit breaker (MCCB)
Maximum allowable rating (A)

Maximum allowable rating by the US National Electrical Code. Exact size must be chosen for each installation.

Select an appropriate molded case circuit breaker with a rating that is suitable for the size of the cable.
Wiring to the power supply and the motor
Refer to the National Electrical Code (Article 310) regarding the allowable current of the cable. Select the cable size for 125%
of the rated current according to the National Electrical Code (Article 430).
For wiring the input (R/L1, S/L2, T/L3) and output (U, V, W) terminals of the inverter, use the UL listed copper, stranded wires
(rated at 75°C) and round crimping terminals. Crimp the crimping terminals with the crimping tool recommended by the
terminal maker.
Short circuit ratings
• 400 V class
Suitable For Use in A Circuit Capable of Delivering Not More Than 100 kA rms Symmetrical Amperes, 500 V Maximum.
122
APPENDIX
Instructions for UL and cUL
00023 00038 00052
(0.75K) (1.5K) (2.2K)
500 V or more
6 10 10
15 15 15

00620 00770 00930
(30K) (37K)
500 V or more
125 150 175
150 175 225

00083 00126
(3.7K) (5.5K)
15 25
20 30
01160 01800
(45K) (55K) (75K)
200 250
250 450
00170 00250 00310
(7.5K) (11K) (15K)
35 60 70
40 60 70
02160 02600 03250
(90K) (110K) (132K)
300 350 400
450 500 ―
00380 00470
(18.5K) (22K)
90 100
90 100
03610
(160K)
500
―