Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec Speedy 500
Summary of Contents for Trotec Speedy 500
- Page 1 Pre-Installation Instructions 8014 Trotec Speedy 500...
-
Page 2: Table Of Contents
4.3 General notes regarding Trotec chillers ....................14 4.4 Water Requirements for chiller and laser tube..................14 5 Installation Preview ....................... 15 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 2 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... -
Page 3: Laser Machine Requirements
Mass of the machine 1210 - 1320 lbs (depending on laser power) 1300 mm Min. door width 51 in. 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 3 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... -
Page 4: Unloading Of The Crate And Machine
The machine must be allowed to stand for 24 hours before use. 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 4 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... -
Page 5: Floor Plan For The Speedy 500
Head Exhaust- Connection 440mm 440mm 17.32” 17.32” 115mm 190mm 4.53” 7.48” Chiller, Gas, Compressed Air inlet 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 5 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... -
Page 6: Operating Environment And Safety
3mm from wheel to wheel. An uneven surface may cause a twisting of the main enclosure. This can cause motion system binding as well as engraving problems. 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 6 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto:... -
Page 7: Electrical Requirements
L – L: 400V L – L: L - N: 230V 208/230V Power consumption 3100W 3100W 3100W 4500W 4500W 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 7 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... - Page 8 Cable length: 5 m / 16 ft Female connectors on machine side are the following: 60W – 120W: 200W: 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 8 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com...
-
Page 9: Electrical Connection
If installing any of these devices, make sure that they meet the electrical requirements of the laser system. It is your responsibility to provide a suitable electrical supply. 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 9 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... -
Page 10: Gas Requirements For Gas Kit
6 mm / 0.23” outside diameter. Gases to be used: • Compressed air • Argon • Nitrogen • Inert gas 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 10 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... -
Page 11: Computer And Software Requirements
USB port for I-Cut Dongle • Serial port (preferred) or USB port for connection between PC and Laser 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 11 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto: techsupport@troteclaser.com... -
Page 12: Software Recommendation
• Camera software - I-Cut Trotec software has been designed to interpret objects either as engraving or as cutting objects. If you use the Trotec printer driver interface and the line thickness (object dimension) exceeds 0.2 mm items will be engraved, if the smallest possible line thickness that your Desktop publishing program offers is chosen (e.g. -
Page 13: Exhaust Requirements
Exhaust Requirements Exhaust Requirements Trotec advises to use the Atmos Duo Plus for the Speedy 500. If only a Cutting table is installed, a VENT 3000 would be sufficient The laser may only be operated with properly installed and operating exhaust system. -
Page 14: Water Chiller Requirements
In case of deviations of water quality, it is recommended to us softening agents, corrosion inhibitors or biocide additives. 13/12/2011 Trotec Produktions- und Vertriebs GmbH_Linzer Strasse 156, A-4600 Wels, Austria, Technical Support 14 / 15 tel_+43 (0)7242 239-7000, fax_+43 (0)7242 239-7380, mailto:... -
Page 15: Installation Preview
Installation Preview The following list gives a preview of the installation procedure. This will assist you to prepare yourself and your premises for the arrival of your new Speedy 500. 1.) Tools for initial installation a. Power screwdriver + set of bits b.