Related Manuals for Trotec 8012 Speedmarker CL
Summary of Contents for Trotec 8012 Speedmarker CL
- Page 1 OPERATION MANUAL 8012 Trotec Speedmarker CL 30W, 45W, air cooled 60W, 100W, 200W, water cooled 14/10/2015 Trotec Laser GmbH 1 / 19...
- Page 2 Trotec Laser GmbH cannot be held responsible for any direct or indirect damages, which result from using or working with the products electric circuits or software described herein. The apparatus must be used only by trained and skilled personnel. Before use the manual should be read and followed carefully.
-
Page 3: Table Of Contents
8012 Trotec Speedmarker CL TABLE OF CONTENTS TABLE OF CONTENTS 1 GENERAL ........................4 1.1 Operation Manual Use – General Information ..................4 1.2 Designated Use ............................5 1.3 Disposal remarks ............................5 1.4 Technical Data / Device Specification ..................... 6 1.5 Manufacturer's Label .......................... -
Page 4: General
8012 Trotec Speedmarker CL GENERAL GENERAL 1.1 Operation Manual Use – General Information Caution: Please read and follow this Operation Manual carefully, before installation and operation. Damage to persons and/or material can result from not following individual points of the... -
Page 5: Designated Use
1.2 Designated Use The SpeedMarker CL is a laser class IV device. The Trotec Speedmarker CL, is an industrial apparatus with a high level of security. To guarantee a safe operation it is necessary to know potential dangers and avoid risks. -
Page 6: Technical Data / Device Specification
8012 Trotec Speedmarker CL GENERAL 1.4 Technical Data / Device Specification Galvo Scanner Standard: 140 x 140 mm (50x50mm – 850x850mm possible) Working area Angular repeatability < 22 µrad Standard: 200 mm (100mm – 1200mm possible) Focal length Beam diameter Standard: 269 µm, 171µm (100mm lens), 1409µm (1200mm... - Page 7 8012 Trotec Speedmarker CL GENERAL Dimensions Dimensions L x W x H [mm] 30W: 832,2 x 278 x 175,5 45W: 832,2 x 278 x 211 For the bending radii of the cables calculate at least additional 60mm in length. 60W: 1432,5 x 278 x 211...
-
Page 8: Manufacturer's Label
8012 Trotec Speedmarker CL GENERAL 1.5 Manufacturer's Label The manufacturer's label is located on the back of the laser source (see Figure below). It is recommended to enter data such as serial number and year of manufacture into the manufacturer's label below so that you always have this data handy if you have problems with your device or require spare parts. -
Page 9: Eu - Declaration Of Conformity
Linzer Strasse 156, A-4600 Wels, OÖ., AUSTRIA hereby declares that the following product Trotec 8012 Speedmarker CL Modell N° 8012 Speedmarker CL 30/45/60/100/200 has demonstrated conformity to the following guidelines: 2006/42/EG Directive for Machines 2006/95/EG Low Voltage Directive 2004/108/EG EMC Guideline... -
Page 10: Safety
8012 Trotec Speedmarker CL SAFETY SAFETY 2.1 General Safety Information All personnel involved in installation, set-up, operation maintenance and repair of the machine, must have read and understood the Operation Manual and in particular the "Safety" section. The user is recommended to generate company-internal instructions considering the professional qualifications of the personnel employed in each case, and the receipt of the instruction/Operation Manual or the participation at introduction/training should be acknowledged in writing in each case. - Page 11 SpeedMarker CL. Most of the laser beam's energy is reflected. Such materials should also not be present in the area of the laser beam. Should you have any additional questions, please contact your integrator or Trotec! 14/10/2015 Trotec Laser GmbH...
-
Page 12: Laser Safety Information
8012 Trotec Speedmarker CL SAFETY 2.2 Laser Safety Information To assess the potential dangers laser systems pose, they are classified into 5 safety classes: 1, 2, 3a, 3b and 4. Speedy 300 is a device of class 4 (USA: Class IV). The safety is to be guaranteed through the Integrator. -
Page 13: Safety Precautions During Switch-On And Operation
8012 Trotec Speedmarker CL SAFETY 2.3 Safety precautions during switch-on and operation Power On/Off switch – main switch Using the main switch on the left hand side, switch the SpeedMarker CL on and off. The key for key switch 2 can only be removed while in the 12 o'clock position. The control circuit is activated in the 3 o'clock position and the laser can be switched on using button 3. -
Page 14: Warning And Information Labels
8012 Trotec Speedmarker CL SAFETY 2.4 Warning and Information Labels Warning and information labels have been placed on the machine in every location that could represent a source of danger prior to start-up or during operation. Please pay special attention to the instructions on the labels. -
Page 15: Prior To Commissioning - Scope Od Delivery
8012 Trotec Speedmarker CL Prior to commissioning – Scope od delivery Prior to commissioning – Scope od delivery The following basic parts are included: 1. Laser source including scanning unit 2. Rack 3. Cabling 4. SP-ICE interface card 5. WeldMark user software, incl. dongle... -
Page 16: Operation
8012 Trotec Speedmarker CL OPERATION OPERATION Prior to start-up and operation of the system, this manual is to be carefully read and the instructions within observed! The SpeedMarker CL is an industrial laser system with a high standard of safety. -
Page 17: Machine View And Connections
8012 Trotec Speedmarker CL OPERATION 4.1 Machine view and connections Scan head Laser pointer (optional) Telescope Laser Source 60-watt SpeedMarker CL water-cooled model Rack 14/10/2015 Trotec Laser GmbH 17 / 19... -
Page 18: Maintenance
1. Switch off the machine. 2. Clean the lens on the underside of the scanner. 3. Clean the housing for the laser source. 5.2 Cleaning the Optical Parts Trotec recommends to use following cleaning material: Lens tissues Part number 69249 Lens cleaner... -
Page 19: Maintenance Plan
8012 Trotec Speedmarker CL MAINTENANCE 5.3 Maintenance Plan Daily Weekly Monthly Annually Laser system Lens Inspect, clean if necessary Housing for laser tubes Cleaning and general housing Entire processing area – Cleaning general cleaning Correct functioning of the Inspect Interlock system...