SeaLevel ISO-16.PCI User Manual
Hide thumbs
Also See for ISO-16.PCI:
- User manual (30 pages) ,
- User manual (21 pages) ,
- User manual (16 pages)
Related Manuals for SeaLevel ISO-16.PCI
Summary of Contents for SeaLevel ISO-16.PCI
- Page 1 ISO-16.PCI Users Manual Part Number 8006 Sealevel Systems, Inc. Telephone: 864.843.4343 155 Technology Place Fax: 864.843.3067 Liberty, SC 29657 USA www.sealevel.com...
-
Page 2: Table Of Contents
B - H ......................8 PPENDIX SSISTANCE C - S ..........................9 PPENDIX CREEN D - C ........................10 PPENDIX OMPLIANCE OTICES ..................10 EDERAL OMMUNICATIONS OMMISSION TATEMENT EMC D ..........................10 IRECTIVE TATEMENT ................................11 ARRANTY ©Revision December 9, 2003 Sealevel Systems, Incorporated. All rights reserved. -
Page 3: Introduction
The ISO-16.PCI provides 16 optically isolated inputs to allow monitoring of off board switch closures, relays or for any other general purpose monitoring needs. The ISO-16.PCI is PCI 2.1 bus compliant. What’s Included The ISO-16.PCI is shipped with the following items. If any of these items is missing or damaged, contact the supplier. •... -
Page 4: Installation
Do not install the Adapter in the machine until the software has been fully installed. 1. Start Windows. 2. Insert the Sealevel Systems CD in to your CD drive. 3. If ‘Auto-Start’ is enabled for this drive the software will automatically launch. Otherwise, point your browser to the ‘Index.htm’... -
Page 5: Physical Installation
4. Gently insert the PCI adapter into the slot. Make sure that the adapter is seated properly. 5. Replace the screw. (This is required to ensure FCC Part 15 compliance.) 6. Replace the cover. 7. Connect the power cord Installation is finished. Sealevel Systems ISO-16.PCI Page 2... -
Page 6: Technical Description
Technical Description Technical Description The ISO-16.PCI provides two parallel input ports. Port A and B are interfaced to optically isolated inputs. Assuming an I/O address of 300 Hex the following table shows the Port Addresses. Base Address Decimal Mode Port A Address... -
Page 7: Pin Assignments
In systems where the users program has direct access to the hardware (DOS) the table below gives the mapping and functions that the ISO-16.PCI provide. The address of each eight-bit port is calculated as shown in the table on the following page, the cards base address plus an offset. -
Page 8: Interrupts
IRQEN = enable interrupts (Base+5) 0 = disabled 1 = enabled (disabled after reset or power up). IRQST = interrupt status (Base+5) 1 = interrupt pending (reading the bit clears interrupt). Bit can not be written. Sealevel Systems ISO-16.PCI Page 5... -
Page 9: Specifications
10 to 90% R.H. Non-Condensing Manufacturing All Sealevel Systems Printed Circuit boards are built to UL 94V0 rating and are 100% electrically tested. These printed circuit boards are solder mask over bare copper or solder mask over tin nickel. Power Consumption... -
Page 10: Appendixa - Troubleshooting
I/O address. 3. Make sure the Sealevel Systems adapter is using a unique IRQ. While the Sealevel Systems adapter does allow the sharing of IRQs, many other adapters (i.e. SCSI adapters & on-board serial ports) do not. The IRQ is typically selected by the BIOS or Operating system. -
Page 11: Appendixb - How T O Get Assistance
3. Sealevel Systems provides an FAQ section on its web site. Please refer to this to answer many common questions. This section can be found at http://www.sealevel.com/faq.asp. -
Page 12: Appendixc - Silk -Screen
Appendix C - Silk-Screen Appendix C - Silk-Screen 3.50" 5.20" 3.175" Sealevel Systems ISO-16.PCI Page 9... -
Page 13: Appendixd - Compliance Notices
Always use cabling provided with this product if possible. If no cable is provided or if an alternate cable is required, use high quality shielded cabling to maintain compliance with FCC/EMC directives. Sealevel Systems ISO-16.PCI Page 10... -
Page 14: Warranty
(RMA) number. The Customer agrees to insure the Product or assume the risk of loss or damage in transit, to prepay shipping charges to Sealevel, and to use the original shipping container or equivalent. Warranty is valid only for original purchaser and is not transferable.