Siemens RUGGEDCOM RSG908C Installation Manual
Rugged ethernet switches
Hide thumbs
Also See for RUGGEDCOM RSG908C:
- Installation manual (48 pages) ,
- Equipment manual (44 pages) ,
- Installation manual (48 pages)
Related Manuals for Siemens RUGGEDCOM RSG908C
Summary of Contents for Siemens RUGGEDCOM RSG908C
- Page 1 Installation Manual SIMATIC NET Rugged Ethernet Switches RUGGEDCOM RSG908C Edition 02/2020 https://www.siemens.com...
- Page 2 Preface Introduction Installing the Device SIMATIC NET Device Management Rugged Ethernet Switches RUGGEDCOM RSG908C Communication Ports Technical Specifications Installation Manual Certification 02/2020 C79000-G8976-1404-06...
- Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommend- ed or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 4: Table Of Contents
Accessing Documentation ....................... v Disclaimer of Liability ......................v Registered Trademarks ......................v Training ..........................vi Customer Support ........................vi Contacting Siemens ....................... vii Introduction ........................... 1 Feature Highlights ....................1 Description ......................2 Required Tools and Materials ................. 3 Decommissioning and Disposal ................ - Page 5 FCC ........................32 6.1.5 FDA/CDRH ......................32 6.1.6 ISED ........................32 6.1.7 TÜV SÜD ......................32 6.1.8 RRA ........................33 6.1.9 RoHS ........................33 6.1.10 Other Approvals ....................33 EMC and Environmental Type Tests ..............34 RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 6: Preface
However, deviations between the product and the documentation may exist. Siemens shall not be liable for any errors or omissions contained herein or for conse- quential damages in connection with the furnishing, performance, or use of this ma- terial. -
Page 7: Training
Siemens Sales representative. Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit http://www.siemens.com/automation/support-request... -
Page 8: Contacting Siemens
Contacting Siemens Address Siemens AG Industry Sector 300 Applewood Crescent Concord, Ontario Canada, L4K 5C7 Telephone Toll-free: 1 888 264 0006 Tel: +1 905 856 5288 Fax: +1 905 856 1995 E-Mail ruggedcom.info.i-ia@siemens.com https://www.siemens.com RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06... - Page 9 Preface Contacting Siemens viii RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 10: Introduction
Introduction The RUGGEDCOM RSG908C is a 8 -port utility-grade, fully managed Ethernet switch specifically designed to operate reliably in electrically harsh and climatically demand- ing environments. • Swappable SFP Transceivers Ports 5 to 87 to 10 can be customized with a wide array of 1000Base-X Small Form-factor Portable (SFP) transceivers offered by Siemens, making the device flexible to the needs of the redundant network application. -
Page 11: Description
Terminal blocks for reliable maintenance free connections • CSA/UL 60950-1 safety approved to 85 °C (185 °F) Description The RUGGEDCOM RSG908C features various ports, controls and indicator LEDs on the front panel for connecting, configuring and troubleshooting the device. POWER LED ALARM LED... -
Page 12: Required Tools And Materials
For information about grounding the device, refer to "Con- necting Power (Page 13)". Required Tools and Materials The following tools and materials are required to install the RUGGEDCOM RSG908C: Tools/Materials Purpose AC power cord (16 AWG) For connecting power to the device. - Page 13 For environmentally friendly recycling and disposal of this device and related acces- sories, contact a facility certified to dispose of waste electrical and electronic equip- ment. Recycling and disposal must be done in accordance with local regulations. RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 14: Installing The Device
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens AG could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment. -
Page 15: Installing The Device In Hazardous Locations
If any item is missing or damaged, contact Siemens for assistance. Installing the Device in Hazardous Locations The RUGGEDCOM RSG908C is designed to comply with the safety standards for Class I, Division 2, Zone 2 hazardous locations where concentrations of flammable gases, vapors or liquids may be present, as opposed to normal operating environments. -
Page 16: Mounting The Device
IMPORTANT Le remplacement de composants pourrait compromettre l'admissibilité à la Classe I, Division 2. Sample Hazardous Location Label The following is an example of the RUGGEDCOM RSG908C hazardous location label: Figure 2.1 Compliance Label (Example) Mounting the Device The RUGGEDCOM RSG908C is designed for maximum mounting and display flexibili- ty. -
Page 17: 2.3.1 Mounting The Device On A Din Rail
2.3.1 Mounting the Device on a DIN Rail The RUGGEDCOM RSG908C can be ordered with a DIN rail adapter preinstalled on the back of the chassis. Use the adapter to mount the device to a standard 35 mm (1.4 in) by 15 mm (0.6 in) IEC/EN 60715 or TS35 DIN rail. -
Page 18: Mounting The Device To A Panel
2.3.2 Mounting the Device to a Panel For panel installations, the RUGGEDCOM RSG908C can be equipped with panel adapters on the top and bottom of the chassis. The adapters allow the device to be attached to a panel using screws. - Page 19 Secure the mounting adapters to the top and bottom of the device using the four M4 screws each included with the device. Screw (M4) Panel Mount Adapter Figure 2.4 Panel Mount Adapter Assembly Prepare mounting holes in the panel where the device is to be installed. RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 20: Connecting The Failsafe Alarm Relay
Control of the failsafe relay output is configurable through RUGGEDCOM RSG908C . One common application for this relay is to signal an alarm if a power failure oc- curs. For more information, refer to the RUGGEDCOM RSG908C User Guide for the RUGGEDCOM RSG908C. - Page 21 Insert the failsafe alarm relay terminal block into the device and tighten the screws. Figure 2.6 Assembling the Failsafe Alarm Relay Terminal Block Connect a failsafe device to the terminal block. Failsafe Alarm Relay Terminal Block Normally Open Common Normally Closed Figure 2.7 Failsafe Alarm Relay Wiring RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 22: Connecting Power
Installing the Device 2.5 Connecting Power Connecting Power The RUGGEDCOM RSG908C features two input terminals that allow the device to be powered by: • Up to one independent AC and one independent DC power source • Two independent DC power sources IMPORTANT •... - Page 23 Connect the Positive wire to the Positive Terminal positive (+) terminal on the termi- Figure 2.9 Terminal Block Wiring nal block. Connect the Negative wire to the negative (-) terminal on the termi- nal block. RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 24: 2.5.2 Wiring Examples
M4 Screw M4 Ring Lug Figure 2.10 Chassis Ground Connection Connect the power cable to the power source. 2.5.2 Wiring Examples The following illustrate how to connect single and dual power supplies to the device. RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06... - Page 25 Installing the Device 2.5.2 Wiring Examples HI Power Supply Configurations Figure 2.11 Single High AC Power Input Figure 2.12 Single High DC Power Input Configuration Configuration RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
- Page 26 Installing the Device 2.5.2 Wiring Examples Figure 2.13 Dual High AC and DC Power Figure 2.14 Dual High DC Power Supplies Supplies RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
- Page 27 Installing the Device 2.5.2 Wiring Examples LO Power Supply Configurations Figure 2.15 Single Low DC Power Input Figure 2.16 Dual Low DC Power Input Configuration Configuration RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 28: Device Management
For Microsoft Windows users, the RUGGEDCOM USB Serial Console driver must be installed on the users workstation before connecting via the USB Type-B console port. For more information, refer to the RUGGEDCOM RSG908C User Guide for the RUGGEDCOM RSG908C. Use the following settings to connect to the port:... -
Page 29: Configuring The Device
Ethernet Ports Connect any of the available Ethernet ports on the device to a management switch and access the RUGGEDCOM RSG908C console and Web interfaces via the device's IP address. The factory default IP address for the RUGGEDCOM RSG908C is https://- 192.168.0.1. -
Page 30: Communication Ports
Fiber Optic (100Base-FX) Ethernet Ports Fiber Optic Ethernet Ports The RUGGEDCOM RSG908C features four fixed Fiber optic Ethernet ports, each with an LC (Lucent Connector) connector. Make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. -
Page 31: Sfp Transceivers
"Fiber Optic Eth- ernet Port Specifications (Page 25)". SFP Transceivers The RUGGEDCOM RSG908C supports up to four Small Form-Factor Pluggable (SFP) transceiver sockets, which are compatible with a wide array of SFP transceivers avail- able from Siemens. LEDs Each socket features an LED that indicates its link state. -
Page 32: Technical Specifications
88 VDC 300 VDC 125 VDC, 3.15 A 5 kVDC 15.3 W 250 VDC 85 VAC 264 VAC 110 VAC, 3.15 A 5 kVDC 15.5 W 220 VAC Current consumption may vary based on configuration. RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06... -
Page 33: Failsafe Alarm Relay Specifications
Link Aggregation ü IEEE 802.3u 100Base-FX ü IEEE 802.3x Flow Control ü ü ü IEEE 802.3z 1000Base-LX ü IEEE Precision Time Protocol (PTP) ü ü ü 1588-2008 Version 2 RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06... -
Page 34: Fiber Optic Ethernet Port Specifications
3 dBm. To convert from peak to average, subtract 3 dBm. • Maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associate when determining maximum segment distances. Operating Environment The RUGGEDCOM RSG908C is rated to operate under the following environmental conditions. -
Page 35: Dimension Drawings
Technical Specifications 5.7 Dimension Drawings Dimension Drawings Note All dimensions are in millimeters, unless otherwise stated. 162.72 Figure 5.1 Overall Dimensions 38.1 163.12 Figure 5.2 Panel Mount Dimensions RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06... - Page 36 Technical Specifications 5.7 Dimension Drawings 162.72 Figure 5.3 DIN Rail Mount Dimensions RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
- Page 37 Technical Specifications 5.7 Dimension Drawings RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
-
Page 38: Certification
Certification The RUGGEDCOM RSG908C device has been thoroughly tested to guarantee its con- formance with recognized standards and has received approval from recognized reg- ulatory agencies. Approvals This section details the standards to which the RUGGEDCOM RSG908C complies. 6.1.1 This device meets the requirements of the following Canadian and U.S. standards un- der certificate CSA 18CA70171440: •... -
Page 39: 6.1.2 Csa/Sira
When marked with the following ATEX marking, this device is approved for use in Zone 2 hazardous locations under certificate Sira 18ATEX4069X. Note For the maximum ambient temperature, refer to the hazardous location label affixed to the device. II 3 G Ex nA nC IIC T4 Gc RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06... -
Page 40: European Union (Eu)
Electromagnetic compatibility of multimedia equipment – Emission requirements The device is marked with a CE marking and can be used throughout the European community. A copy of the CE Declaration of Conformity is available from Siemens AG. For contact information, refer to "Contacting Siemens (Page vii)". -
Page 41: 6.1.4 Fcc
Title 21 Code of Federal Regulations (CFR) – Chapter I – Sub-chapter J – Radiolog- ical Health 6.1.6 ISED This device is declared by Siemens AG to meet the requirements of the following ISED (Innovation Science and Economic Development Canada) standard: • CAN ICES-3 (A)/NMB-3 (A) 6.1.7... -
Page 42: Rra
Republic of Korea (South Korea) as a Class A product in a commercial, industrial or business environment. R-REM-S14-RSG908C A copy of the KC Declaration of Conformity is available from Siemens AG. For contact information, refer to "Contacting Siemens (Page vii)". -
Page 43: Emc And Environmental Type Tests
Railway applications – Electromagnetic Compatibility – Rolling Stock Apparatus • EN 50155 Railway applications – Rolling stock – Electronic equipment EMC and Environmental Type Tests The RUGGEDCOM RSG908C has passed the following Electromagnetic Compatibility (EMC) and environmental tests. EMC Type Tests Test Description... - Page 44 EMC Immunity Type Tests per IEEE 1613 Note The RUGGEDCOM RSG908C meets Class 2 requirements for an all-fiber configuration and Class 1 requirements for copper ports. Class 1 allows for temporary communica- tion loss, while Class 2 requires error-free and interrupted communications.
- Page 45 Class 2 IEC 60255-21-2 Shock 30 g @ 11 ms Class 2 IEC 60255-21-2 Bump 10 g @ 16 ms Class 1 IEC 60255-21-3 Seismic Method A Class 2 IEC 60529 Ingress Protection IP4x RUGGEDCOM RSG908C Installation Manual, 02/2020, C79000-G8976-1404-06...
- Page 46 Further Information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens AG Digital Industry Process Automation Postfach 48 48 90026 NÜRNBERG GERMANY...