TABLE OF CONTENTS EC REGULATIONS AND SECURITY SAFETY INSTRUCTIONS SYSTEM DESCRIPTION CONTROLS OSD MENU INPUT CONNECTORS PACKING INSTRUCTIONS WARNING AHNET PROTOCOL INPUT SIGNALS INFORMATION ON DISPOSAL WARRANTY TERMS AND CONDITIONS...
Page 4
WELCOME Thank you for purchasing an ARTHUR HOLM product. Our product range has been designed to create the perfect meeting room, where the screens are a part of the interior design as well as an essential communication tool. Please, read this installation and operating instructions carefully and keep them in a safe place for future reference.
Page 5
ABOUT US The Company Arthur Holm has its origins in the Danish furniture designer Jorgen Alex Jensen, who was active during the sixties and the seventies. His design inspiration and his concept of ergonomics have been continued by his family, the design force behind Arthur Holm product range. The result of...
EC REGULATIONS AND SECURITY ATTENTION: Do not disassemble or modify the device in any way. This symbol warns of the presence of dangerous un-insulated voltages inside some of the components, of sufficient magnitude to expose people to risk of electronic shock. This symbol draws attention to important use and maintenance instructions in the manual that accompanies the unit.
Page 7
SAFETY INSTRUCTIONS Wiring connected to hazardous voltage requires installation by qualified personnel or the use of ready-made flexible cables. For your security, your equipment must be connected to an electrical outlet with grounding connection protection. Since the plug is used to disconnect the device, the operating electrical outlet must be in an easily accessible place.
∙ Meeting rooms ∙ Board rooms ∙ Auditoriums ∙ Information desks ∙ Training rooms Features • TFT Active Matrix display AH15D X2HDGA FULL HD 15.6" AH17D X2HDGA FULL HD 17.3" AH19D X2HDGA FULL HD 18.5" AH22D X216GA FULL HD 21.5"...
Page 9
SYSTEM DESCRIPTION • Electrical powered lift system with variable speed. • Addressable RS422 monitor control by AHnet protocol, RJ45 connector CAT5. Box Contents Before the installation of your retractable monitor, please check the contents of the shipping box, it must contain the following items: •...
CONTROLS Remote IR control POWER Switch ON/OFF the monitor MENU Activates the OSD menu on screen Cursor control up on the OSD menu DOWN Cursor control down on the OSD menu LEFT Cursor control left on the OSD menu RIGHT Cursor control right on the OSD menu Selects the function on the OSD menu.
Page 11
CONTROLS IR sensor The IR sensor is located on the lower right side of the screen. Monitor movement controls On the upper cover plate, there are two buttons to control the UP and DOWN monitor movements. 2. UP BUTTON CONTROL 1.
OSD MENU Accessing the menu system • With the OSD off, push the MENU button to activate the main OSD menu. • Press the UP and DOWN buttons to move from one function to another. Please refer to the following sections below to view a complete list of all the functions available for the monitor.
Page 13
OSD MENU Screen ARC: Adjusts the image aspect on screen ∙ 16:9: Shows the image on screen with 16:9 aspect ∙ 4:3: Shows the image on screen with 4:3 aspect ∙ Just scan Noise Reduction: Adjusts the image noise filter ∙...
Page 14
OSD MENU Setup Language: OSD language selection Restore Factory Default: Adjusts the parameters to the initial factory parameters Blending: OSD window transparency ∙ Low ∙ Medium ∙ High ∙ Off OSD Duration: Adjusts the time that the OSD menu window remains on screen Software Update: Used for firmware upgrade mirror Mirror:...
INPUT CONNECTORS DVI 1/ DVI A DVI-I input signal: Connect a DVI (digital) input signal and select DVI 1 on the OSD monitor menu. Use a DVI to VGA adapter to connect an ARGB (analogue) input signal and select DVI-A on the OSD monitor menu.
PACKING INSTRUCTIONS ATTENTION ! Albiral Display Solutions, s.l. c/Fátima 25, 08512 BCN - Spain tel. +34 938 502 376 www.arthurholm.com /www.albiral.com Thank you for purchasing our product, we hope you are completely satisfied with it. If you have any questions you can contact us by email customersupport@arthurholm.com or by phone +34 938 502 376 office hours 9am - 2pm &...
WARNING Do not use the unit in horizontal position. It could damage the mechanical parts of the monitor. Do not use force to open or close the monitor. It could damage the mechanical parts of the monitor. Use this device only with the supplied accessories. The use of unapproved accessories, as a power supply unit, will invalid the warranty.
AHNET PROTOCOL Communications protocol COMMUNICATION RS422 CONNECTION RJ45 WIRING CAT-5 Speed and configuration BAUD RATE 38400 DATA BITS PARITY NONE STOP BITS Wiring Diagram 1. Data TX + 2. Data TX – 3. Data RX + 4. NC 5. NC 6 .Data RX RJ-45 7.
Page 19
AHNET PROTOCOL AHnet protocol Using 5 bytes communication: BYTE 0 START BYTE BYTE 1 ADDRESS BYTE BYTE 2 COMMAND BYTE BYTE 3 VALUE 1 BYTE 4 VALUE 2 Commands COMMAND DESCRIPTION RESPONSE FA XX 01 01 00 GO UP FB XX 01 01 00 FA XX 01 00 00 GO DOWN FB XX 01 00 00...
Page 20
AHNET PROTOCOL BITE CLOSED OPENED SCREEN ON SCREEN OFF DVI-A DVI 1-D DVI 2-D PROTECTION STOP MONITOR OK BITE BUTTON LOCK BUTTON UNLOCK To send an order to all the monitors, you must use the address: 249 Dec. (Byte1) F9 Hex. (Byte1) In this case, the units do not send a reply.
Page 21
AHNET PROTOCOL Picture Commands COMMAND DESCRIPTION RESPONSE FA XX 15 00 00 ASK FOR BACKLIGHT LEVEL FB XX 15 00 ZZ FA XX 16 00 00 ASK FOR CONTRAST LEVEL FB XX 16 00 ZZ FA XX 17 00 00 ASK FOR BRIGHTNESS LEVEL FB XX 17 00 ZZ Number of the monitor address.
INFORMATION ON DISPOSAL FOR USERS OF WASTE ELECTRICAL & ELECTRONIC EQUIPMENT This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to the designated collection points, where they will be accepted on a free of charge basis.
WARRANTY TERMS AND CONDITIONS Albiral Display Solutions warrants this product against manufacturing defects and workmanship for a period of five (5) years from the date of purchase, subject to the conditions below. Mechanical parts: The engine and the product’s mechanical parts are warranted against manufacturing defects and workmanship for a period of five (5) years from the date of purchase.