ARTHUR HOLM AH17D X2HDGA TALK User Manual
Retractable monitors for furniture integration with integrated dynamictalk
Hide thumbs
Also See for AH17D X2HDGA TALK:
- User manual (56 pages) ,
- User manual (14 pages) ,
- User manual (37 pages)
Related Manuals for ARTHUR HOLM AH17D X2HDGA TALK
Summary of Contents for ARTHUR HOLM AH17D X2HDGA TALK
- Page 1 User manual AH17D X2HDGA TALK AH22D X216GA TALK Retractable monitors for furniture integration with integrated DynamicTalk...
-
Page 3: Table Of Contents
Table of contents EC REGULATIONS & SECURITY SAFETY INSTRUCTIONS APPLICATIONS BOX CONTENTS FEATURES CONTROLS OSD MENU INPUT CONNECTORS DYNAMICTALK HANDLING WARNING MONITOR AHnet PROTOCOL DYNAMICTALK AHnet PROTOCOL INPUT SIGNALS PRODUCT WARRANTY... - Page 5 Welcome Thank you for purchasing an ARTHUR HOLM product. Our product range has been designed to create the perfect meeting room, where the screens are a part of the interior design as well as essential communication tools. Please, read this installation and operating instructions carefully and keep them in a safe place for future reference.
-
Page 6: Ec Regulations & Security
EC Regulations and Security ATTENTION: Do not disassemble or modify the device in any way. This symbol warns of the presence of dangerous un-insulated voltages inside some of the components, of sufficient magnitude to expose people to risk of electronic shock. This symbol draws attention to important use and maintenance instructions in the manual that accompanies the unit. -
Page 7: Safety Instructions
Safety instructions PLUGS – Do not dismantle any part of the monitor power connector – Disconnect the power plug from the AC outlet when the monitor is not going to be used for an indefinite period of time POWER AND EXTENSIONS CORDS –... -
Page 8: Applications
System Description APPLICATIONS The DynamicX2Talk system is a professional TFT display with DynamicTalk and an electrical lift system for installation into a horizontal furniture surface. The DynamicTalk system is a universal motorized microphone lift system remotely controllable through RS422 or GPI with Dynamic LED Ring for “Ready to Talk” and “Talk”... -
Page 9: Features
System Description FEATURES - TFT Active Matrix display AH17D X2HDGA TALK FULL HD 17" AH22D X216GA TALK FULL HD 22" – Retractable monitor with electrical engine for furniture integration and tilting screen 20° (factory adjusted) with integrated universal XLR3 microphone lift system... -
Page 10: Controls
Controls OSD MONITOR CONTROL The OSD buttons, to control or configure the monitor, are located at the lower body housing of the system POWER SOURCE RIGHT LEFT DOWN SELECT MENU POWER Monitor power on/off Indicates operation status SOURCE Signal input selection RIGHT Cursor control right on OSD menu LEFT... - Page 11 Controls REMOTE CONTROL POWER Switch ON/OFF the monitor MENU Activates the OSD menu on screen DOWN Cursor control down on the OSD menu. Selects the input source when the OSD menu is not active on screen, Cursor control up on OSD menu LEFT Cursor control left on OSD menu RIGHT...
- Page 12 Controls On the upper cover plate, there are two buttons to control the UP and DOWN monitor movements and three buttons to control the DynamicTalk functions and to external control other devices (GPO): 1. Retracting the monitor: It is recommended that no objects or parts of the body that could obstruct the retracting movement of the display, are not on the top of the cover plate.
- Page 13 Controls 4. Customized button: The central push button is used to control external devices. The contact close button (GPO) is present on SubD9 connector to external control other devices 5. TALK or GPO button: The third push button has two different functions: - PA mode: In PA mode, this button is used as "Mute"...
-
Page 14: Osd Menu
OSD menu ACCESSING THE MENU SYSTEM – With the OSD off, push the MENU button to activate the main OSD menu – Press the UP and DOWN button to move from one function to another. As you move from one icon to another, the function name changes to reflect the function or group of functions represented by that icon. - Page 15 OSD menu SCREEN Input Input signal selection DVI-A DVI 1 DVI 2 Aspect image on screen Full The image is showed on full screen 16:9 Shows the image on screen with 16:9 aspect Aspect Shows the image on full screen but keeps the original aspect ratio of the input image Shows the image on screen with 4:3 aspect Shows the image on screen with the...
- Page 16 OSD menu SETUP Language OSD language selection PC Control Adjust the image on screen. Only on ARGB (analogue) input H-Pos Adjust the image on screen horizontally V-Pos Adjust the image on the screen vertically Phase Adjust the phase Clock Adjust the clock Auto Adjust Auto adjust the image on screen Reset...
-
Page 17: Input Connectors
Input connectors DVI 1/ DVI A DVI-I input signal. Connect a DVI (digital) input signal and select DVI 1 on the OSD monitor menu. Use a DVI to VGA adapter to connect an ARGB (analogue) input signal and select DVI-A on the OSD monitor menu DVI 2 DVI-D input signal. - Page 18 Input connectors MICROPHONE INPUT CONNECTORS Microphone out: XLR3 microphone connector installed in the DynamicTalk 12V D.C.IN: XLR4 connector to the power supply 1,2: Ground 3,4: 12Vdc GPI: SubD 9 pins female connector to contact close external functions FUNCTION Contact close of the customised push button on upper cover plate (middle button).
- Page 19 Input connectors MICROPHONE INPUT CONNECTORS Settings: 6 dip switch to configure the DynamicTalk. DIP SWITCH FUNCTION Dynamic Talk configured in PA mode. The T push button controls the microphone mute function OFF: DynamicTalk configured in conference mode. The 1,2,3 TALK push button has no function, the contact close is available on GPO connector and the LED ring is controlled externally (GPI) Factory only.
- Page 20 Input connectors MICROPHONE LENGTH SETTING PROCEDURE DynamicTalk is designed to work with microphones of different lengths. Two signs to identify an incorrect setup of the microphone length are: - The microphone do not goes down completely. - The microphone goes down too slowly and gets stuck inside. The microphone length can be adjusted using the Monitor Configurator Tool, but there is also a quick procedure that doesn’t require the use of a PC or cable:...
-
Page 21: Dynamictalk Handling
DynamicTalk Handling Please follow the figure below for a correct product usage of the DynamicTalk microphones. To avoid any product malfunctions, do not attempt to bend the microphone to the incorrect angle or outside the microphone's working area, as indicated on the picture below. Please note that ware to the microphone and pop screen surface can occur. -
Page 22: Warning
Warning Before connecting the monitor, open the hatch and remove the 2 foam protection pieces. Do not use the unit in horizontal position. It could damage the mechanical parts of the monitor. Do not use force to open or close the monitor. It could damage the mechanical parts of the monitor. -
Page 23: Monitor Ahnet Protocol
Monitor AHnet protocol COMMUNICATIONS PROTOCOL Communication RS422 Connection RJ45 Wiring CAT-5 SPEED & CONFIGURATION Baud Rate 38400 Data Bits Parity None Stop Bits WIRING DIAGRAM Data TX + Data TX – Data RX + Data RX RJ-45 CONNECTION Pins 1 & 2 The units respond Pins 3 &... - Page 24 Monitor AHnet protocol AHnet PROTOCOL Using 5 bytes communication: BYTE 0 START BYTE BYTE 1 ADDRESS BYTE BYTE 2 COMMAND BYTE BYTE 3 VALUE 1 BYTE 4 VALUE 2 COMMANDS COMMAND DESCRIPTION RESPONSE FA XX 01 01 00 GO UP FB XX 01 01 00 FA XX 01 00 00 GO DOWN...
- Page 25 Monitor AHnet protocol BITE CLOSED OPENED SCREEN ON SCREEN OFF DVI-A DVI 1-D DVI 2-D PROTECTION STOP MONITOR OK BITE BUTTON LOCK BUTTON UNLOCK To send an order to all the monitors, you must use the address: 249 Dec. (Byte1) F9 Hex.
-
Page 26: Dynamictalk Ahnet Protocol
DynamicTalk AHnet protocol COMMUNICATIONS PROTOCOL Communication RS422 Connection RJ45 Wiring CAT-5 SPEED & CONFIGURATION Baud Rate 38400 Data Bits Parity None Stop Bits WIRING DIAGRAM Data TX + Data TX – Data RX + Data RX - RJ-45 CONNECTION Pins 1 & 2 The units respond Pins 3 &... - Page 27 DynamicTalk AHnet protocol AHnet PROTOCOL Using 5 bytes communication: BYTE 0 START BYTE BYTE 1 ADDRESS BYTE BYTE 2 COMMAND BYTE BYTE 3 VALUE 1 BYTE 4 VALUE 2 COMMANDS COMMAND DESCRIPTION RESPONSE FA XX 01 01 00 GO UP FB XX 01 01 00 FA XX 01 00 00 GO DOWN...
- Page 28 DynamicTalk AHnet protocol BITE 0 TOP POSITION BITE 1 DOWN POSITION BITE 2 (1) MUTE ON BITE 3 (1) BUTTON LOCK BITE 4 BITE 5 BITE 6 BITE 7 (1) FAILURE IN THE SYSTEM To send an order to all the devices, you must use the address: F7 Hex.
-
Page 29: Input Signals
Input Signals AH17D X2HDGA TALK/ AH22D X216GA TALK RESOLUTION Horizontal freq (KHz) Vertical freq (Hz) Scanning type 800x600@60Hz 37.879 60.317 Progressive 800x600@72Hz 48.077 72.188 Progressive 800x600@75Hz 46.875 75.000 Progressive 1024x768@60Hz 48.363 60.005 Progressive 1024x768@70Hz 56.476 70.070 Progressive 1024x768@75Hz 60.023 75.030... - Page 30 Information on Disposal for users of waste Electrical & Electronic equipment This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
-
Page 31: Product Warranty
LIMITED 2-YEAR WARRANTY LCD PANEL, LCD PANEL INVERTER, LCD CONTROLLER & POWER SUPPLY The electric parts of the Arthur Holm are warranted to be free from manufacturing defects for a period of two 2 years from the date of purchase. - Page 32 Patents ES 1051718UU ES 1061088UU EP 1574150A1 ES 1068395 U WO 2009141744 Fàtima 25, Sant Hipòlit de Voltregà MU 170180 ES00 08512 Barcelona – Spain EP 2289367 A1 tel: +34 93 850 23 76 / 23 83 MU 17301 ES00 fax: +34 93 850 25 50 / 23 72 MU 17322 ES00 web: www.arthurholm.com...