TABLE OF CONTENTS EC REGULATIONS AND SECURITY SAFETY INSTRUCTIONS SYSTEM DESCRIPTION BEFORE INSTALLATION INPUT CONNECTORS CONTROLS OSD MENU AHNET PROTOCOL INPUT SIGNALS INFORMATION ON DISPOSAL WARRANTY TERMS AND CONDITIONS...
Page 4
WELCOME Thank you for purchasing an ARTHUR HOLM product. Our product range has been designed for a seamless integration and for a maximum reliability. Please, read this installation and operating instructions carefully and keep them in a safe place for future reference.
Page 5
ABOUT US The Company Arthur Holm has its origins in the Danish furniture designer Jorgen Alex Jensen, who was active during the sixties and the seventies. His design inspiration and his concept of ergonomics have been continued by his family, who is the design force behind Arthur Holm product range. The...
EC REGULATIONS AND SECURITY ATTENTION: Do not disassemble or modify the device in any way. This symbol warns of the presence of dangerous un-insulated voltages inside some of the components, of sufficient magnitude to expose people to risk of electronic shock. This symbol draws attention to important use and maintenance instructions in the manual that accompanies the unit.
Page 7
SAFETY INSTRUCTIONS • Make sure the total ampere passed through a extension cord does not exceed the maximum allowed by the cable used. • Do not place anything on the power cord. • Do not locate this product where a person may walk or trip over the cord.
SYSTEM DESCRIPTION Applications The Dynamic3 system, is a professional TFT display with an elegant housing and an electrical system, for installation into a horizontal furniture surface. The mechanism offers horizontal and vertical working positions. With the push of a button, the monitor is lifted. Giving it a 180˚ turn, the monitor is ready to be folded down until leveled with the desk surface.
SYSTEM DESCRIPTION Important note: This device can only work with the power supply included in the shipping box. This power supply can not be replaced by any other rather than the original one. BEFORE INSTALLATION Make sure to follow these steps before installing the device: Remove the 2 lateral transport plastic screws M8x30 Remove the 2 lateral transport plastic screws M8x30...
Page 10
BEFORE INSTALLATION Follow the next steps to pack the device for a safe shipment: Picture (A): Dynamic3 with Picture (B): Dynamic3 with external control buttons cover plate Press and hold button 1 until the monitor housing gets released from the frame.
INPUT CONNECTORS DVI 1/DVI A: DVI-I input signal. Connect a DVI (digital) input signal and select DVI 1 on the OSD monitor menu. Use a DVI to VGA adapter to connect an ARGB (analogue) input signal and select DVI-A on the OSD monitor menu.
Page 12
INPUT CONNECTORS Termination: Activate (ON) the termination, ONLY on the last unit of the RS422 bus. AHnet: RJ45 CAT5 connector for addressable RS422 control. There is a loop through connector to use as signal RS422 output. Up to 30 monitors can be connected on the same RS422 bus.
CONTROLS OSD monitor control In order to access to the OSD monitor control menu, use the IR remote control supplied with the monitor: POWER Switch ON/OFF the monitor MENU Activates the OSD menu on screen Cursor control up on the OSD menu DOWN Cursor control down on the OSD menu LEFT...
Page 14
CONTROLS Monitor movement controls On the upper cover plate, there are three buttons to control the UP and DOWN monitor movements. 1. OPEN CONTROL BUTTON 2. CLOSE CONTROL BUTTON, FACE UP 3. CLOSE CONTROL BUTTON, FACE FOWN 1. Raising the monitor: To raise and tilt the monitor display, press the open button (1) on the right hand side of the cover plate.
OSD MENU Accessing the menu system • With the OSD off, push the MENU button to activate the main OSD menu. • Press the UP and DOWN buttons to move from one function to another. Please refer to the following sections below to view a complete list of all the functions available for the monitor.
Page 16
OSD MENU Picture Noise Reduction: Adjusts the image noise filter ∙ Off ∙ Low ∙ Medium ∙ High ∙ Default Screen (Only for analogue signals): ∙ Auto Adjust ∙ Horizontal Position ∙ Vertical Position ∙ Size ∙ Phase Backlight: Adjusts the backlight screen level Colour Range: Adjusts the colour range ∙...
Page 17
OSD MENU Option Language: Selects the OSD language Restore Factory Default: Adjusts the parameters as factory Blending: OSD window transparency ∙ Low ∙ Middle ∙ High ∙ Off OSD Duration: Adjusts the time that the OSD menu window remains on screen Software Update (USB): Used for firmware upgrade Mirror:...
AHNET PROTOCOL Communications protocol COMMUNICATION RS422 CONNECTION RJ45 WIRING CAT-5 Speed and configuration BAUD RATE 38400 DATA BITS PARITY NONE STOP BITS Wiring Diagram 1. Data TX + 2. Data TX – 3. Data RX + 4. NC 5. NC 6 .Data RX –...
Page 19
AHNET PROTOCOL AHnet protocol Using 5 bytes communication: BYTE 0 START BYTE BYTE 1 ADDRESS BYTE BYTE 2 COMMAND BYTE BYTE 3 VALUE 1 BYTE 4 VALUE 2 Commands COMMAND DESCRIPTION RESPONSE FA XX 01 00 00 GO DOWN, BOTTOM FB XX 01 00 00 FA XX 01 01 00 GO UP + INCLINATION...
Page 20
AHNET PROTOCOL Picture Commands COMMAND DESCRIPTION RESPONSE FA XX 15 00 00 ASK FOR BACKLIGHT LEVEL FB XX 15 00 ZZ FA XX 16 00 00 ASK FOR CONTRAST LEVEL FB XX 16 00 ZZ FA XX 17 00 00 ASK FOR BRIGHTNESS LEVEL FB XX 17 00 ZZ Number of the monitor address.
Page 21
AHNET PROTOCOL BITE CLOSED OPENED CLOSED MONITOR 90˚ SCREEN ON SCREEN OFF DVI-A DVI 1 DVI 2 PROTECTION STOP MONITOR OK BITE BUTTON LOCK BUTTON UNLOCK...
INFORMATION ON DISPOSAL FOR USERS OF WASTE ELECTRICAL & ELECTRONIC EQUIPMENT This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to the designated collection points, where they will be accepted on a free of charge basis.
WARRANTY TERMS AND CONDITIONS Albiral Display Solutions warrants this product against manufacturing defects and workmanship for a period of two (2) years from the date of purchase, subject to the conditions below. 1. LCD panel, inverter, controller, electrical, electronic boards, accessories and power supply are warranted against manufacturing defects and workmanship for a period of two (2) years from the date of purchase.