Table of Contents
Advertisement
Chapter 2 - Hardware Installation
Board Layout
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select
(JP4)
COM1 RS232/422/485
(JP2)
Select
COM2 RS232/422/485
(JP11)
5
1
5
1
Select
(JP3)
PS/2 KB/MS
COM1 RS232/Power
(JP3)
1
1
Select
USB 8-9
6
2
6
2
(JP4)(JP1)
(JP14)
USB 2.0
1 5
COM2 RS232/Power
(JP14)
Select
6
5
2
1
(JP2)
4 8
6
5
COM2
COM1
2
1
(JP11)
ASMedia
ASM1442
DVI-I
HDMI
ASMedia
ASM1442
USB 0-1 Power
Select (JP5)
1
LAN 1
USB 0-1
USB 3.0
Intel
WGI217LM
LAN 2
USB 4-5
1
USB 4-5 Power
USB 3.0
Select (JP6)
Line-in
Line-out
Intel
Mic-in
WGI210AT
PCIe x16 (x16 signal)
Realtek
ALC886
PCIe x1
S/PDIF
1
2
10
1
9
PCIe x16 (x1 signal)
Front
Audio
PCIe x4
DIO 3/5/7/9
Output State (JP12)
DIO 11/13/15/17
Output State (JP7)
19
1
DIO
DIO Power Select
2
(JP13)
1 1 1
Chapter 2 Hardware Installation
2
26
Chassis
1
intrusion
CPU Fan
1
Parallel
25
1
+12V
ISL95820
Power
Buzzer
System Fan 2
Socket LGA1150
Battery
DDR3_1
DDR3_3
DDR3_2
DDR3_4
Intel
Q87
SMBus
2
USB 10-11
1
USB 2-3/6-7
Power Select
Power Select
1
Clear CMOS
(JP8)
(JP18)
SATA DOM
Data (JP9)
USB 2.0
USB 2.0
Power Select
(JP17)
USB 10-11
SATA 5
USB 2-3
USB 6-7
9
1
9
1
9
1
1
1
1
1
10
2
10
2
System Fan 1
10
2
Note: SATA5 supports SATA DOM.
Chapter 2
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
2
12
1
1
11
System Memory
LPC
10
9
COM6
2
1
Nuvoton
Important:
NCT6106D
10
9
When the Standby Power LED lit red, it indicates that there is power on the system
COM5
2
1
board. Power-off the PC then unplug the power cord prior to installing any devices.
10
9
COM4
Failure to do so will cause severe damage to the motherboard and components.
2
1
10
9
COM3
2
1
12
24
ATX
DDR3-1
Power
Channel A
DDR3-2
DDR3-3
Channel B
1
13
Power-on
DDR3-4
Select (JP10)
1
Standby
Power LED
1
2
Front
Panel
11
12
SPI Flash
BIOS
SATA 3.0
SATA 1
SATA 0
1
1
Rear I/O
SATA 3
SATA 2
6
Onboard I/O
5
1
1
SATA 3.0
SATA 4
Storage
1
1
Expansion
Features
•
The four DIMM sockets are divided into 2 channels:
Channel A - DDR3_1 and DDR3_2
Channel B - DDR3_3 and DDR3_4
•
Supports
DDR3/DDR3L 1333/1600MHz when operating at 1.5V
•
Supports dual channel memory interface
•
Supports up to 32GB system memory
9
Standby
Power LED
www.dfi .com
Advertisement
Table of Contents
