Error And Warning List - Access Flow2 Manual

2015.04.16

4.1 Error and warning list

F01 Obstruction in current drive direction detected: left
F02 Obstruction in current drive direction detected: right
C04 Level beyond 2 degrees
F05 Level beyond 5 degrees
F06 Drive speed beyond track operating range
F07 Level beyond 7 degrees
F08 Level sensor deviation
F09 Hardware failure of the main drive
F10 Hardware failure of the level drive
F11 Hardware failure of the swivel drive
F12 Drive motor current trip or overvoltage occurred
F13 Level motor current trip or overvoltage occurred
F14 Swivel motor current trip or overvoltage occurred
F15 HALL sensor failure of the main drive
F16 HALL sensor failure of the level drive
F17 HALL sensor failure of the swivel drive
F18 Drive speed beyond maximum limit
F19 Drive speed beyond ELD operating range
F20 Software inconsistency detected (assert)
F21 Battery voltage low while moving up
F22 Battery failure: under or overvoltage detected
F23 Brake circuit failure detected
F24 HW Error detected
F25 Wrong HW/SW combination
Reduce speed failed
F26
Normal stop failed
F27
Emergency stop failed
F28
Disable drive main failed
F29
Stop drive level failed
F30
Stop drive swivel failed
F31
F32 User emergency stop
F33 Overspeed (OSG) tripped
F34 Level sensor failure
F35 Level sensor failure
F36 Level sensor failure
F37 Swivel position outside operating range (+/- 110 deg)
F40 OSG opto failure
F41 ELD opto failure
F42 Swivel zero opto failure
F47 Swivel squeeze opto failure
F49 RF unit is not responding
F50 Failed to read parameters (motor control or application)
F51 Failed to read the track data
F52 Drive position is found to be incorrect
Flow2 - Stairlift
F53 Swivel position is found to be incorrect
F54 Safety code is found to be incorrect
F55 Brownout is triggered while moving
C56 An unexpected negative contact was detected
C58 A negative contact was expected but not detected
C60 The track position value is beyond the maximum track length
C61 The swivel sync opto 0 is detected at an unexpected swivel position
C62 The swivel sync opto has an inverted value
F63 Main drive moment detected without user input
F64 Level drive moment detected without user input
F65 Swivel drive moment detected without user input
F66 Wrong direction detected for main drive
F67 Wrong direction detected for level drive
F68 Wrong direction detected for swivel drive
F69 CPU startup check fails (includes code CRC check)
C70 Lift driving in normal mode without test run performed
C71 User emergency maintenance counter elapsed
F72 User emergency maintenance counter elapsed
C73 Position outside track bounds
F74 Manual swivel not in position while starting
F75 Battery voltage below upwards level
F76 Battery voltage recharge required
F77 Drive I²T critical Main
F78 Drive I²T critical Level
C80 Drive I²T warning Main
C81 Drive I²T warning Level
Level sensors are off, but there's drive moment (allowed in service
F83
because of mode -3-)
C85 Backup battery low (below 1.65V)
C86 Level sensor deviation > 4 degrees
C87 Swivel deviation > 10 degrees
S1 HW release circuit failure
S2 Swivel current measurement too low
S3 Swivel current offset calibration failed
S4 Level current offset calibration failed
S5 Drive current offset calibration failed
S6 +15V outside of limits
S7 +5V outside of limits
S8 Reference voltage outside of limits
S9 +3V3 overload
S10 MCU internal failure
S11 Check timeout
S12 Supply enable/disable circuit failure
S13 Main/Level/Swivel overcurrent protection failure
www.ThyssenKruppAccessibility.com
Tab 06: Systematic fault finding