Motor Specifications; Performance Chart - STA-RITE SG12 Series Installation, Operation & Parts Manual

MOTOR SPECIFICATIONS

Model Voltage/
Number HP
SG12200225M 2 208-230/1
SG12200325M 2 208-230/460/1
SG13200225M 2 208-230/1
SG13200325M 2 208-230/460/3
SGC12200225M 2 208-230/1
SGC12200325M 2 208-230/460/3
SGC13200225M 2 208-230/1
SGC13200325M 2 208-230/460/3
SGC20300225M 3 208-230/1
SGC20300325M 3 208-230/460/3
SGC20500225M 5 208-230/1
SGC20500325M 5 208-230/460/3
SGC20750325M 7.5 208-230/460/3 24.3-22.0/11.0

PERFORMANCE CHART

GPM at Total Feet (M)
Model 20(6) 50(15)
Number Capacity Gallons/Minute(LPM)
SG12200225M 44(167) 36(136)
SG12200325M 44(167) 36(136)
SG13200225M 55(208) 45(170)
SG13200325M 55(208) 45(170)
SGC12200225M 44(167) 36(136)
SGC12200325M 44(167) 36(136)
SGC13200225M 55(208) 45(170)
SGC13200325M 55(208) 45(170)
SGC20300225M 104(394) 76(288)
SGC20300325M 104(394) 76(288)
SGC20500225M 116(439) 108(409) 80(303)
SGC20500325M 116(439) 108(409) 80(303)
SGC20750325M 168(636) 150(568) 120(454) 86(326)
Table I: Electrical Nameplate Data
Model HP
SG12200225M 2
SG12200325M 2 208-230/460/60/3
SG13200225M 2
SG13200325M 2 208-230/460/60/3
SGC12200225M 2
SGC12200325M 2
SGC13200225M 2
SGC13200325M 2 208-230/460/60/3
SGC20300225M 3
SGC20300325M 3 208-230/460/60/3
SGC20500225M 5
SGC20500325M 5 208-230/460/60/3
SGC20750325M 7.5 208-230/460/60/3
* Motor RPM is 3450.
NOTICE: Motors rated at 230V/60Hz/1ø may overload if operated on 208 volts. Consult factory before attempting to operate
single phase motors on 208 volts.
Motor Minimum
Max. Load Circuit
Phase Amps Req.(Amp)
12.0
6.6-6.0/3.0
14.0
7.1-6.4/3.2
12.0
6.6-6.0/3.0
14.0
7.1-6.4/3.2
28.0
15.5-14.0/7.0
34.0
20.0-18.0/9.0
No Flow at
80(24) 110(34) Height Shown
Below Ft. (M)
12(45) – 85(26)
12(45) – 85(26)
28(106) 8(30) 116(35)
28(106) 8(30) 116(35)
12(45) – 85(26)
12(45) – 85(26)
28(106) 8(30) 116(35)
28(106) 8(30) 116(35)
15(57) – 84(25.6)
15(57) – 84(25.6)
18(68) 116(35)
18(68) 116(35)
150(46)
Volts/Hz/Ph Amps
230/60/1 12.0
6.6-6.0/3.0
230/60/1 14.0
7.1-6.4/3.2
230/60/1 12.0
208-230/460/3 6.6-6.0/3.0
230/60/1 14.0
7.1-6.4/3.2
230/60/1 28.0
15.5-14.0/7.0
230/60/1 34.0
20.0-18.0/9.0
24.3-22.0/11.0
PIPING DIMENSIONAL GUIDE
20
10/10
30
10/10
20
10/10
30
10/10
50
20/10
Figure 1: Basin Dimensions
60
30/20
30/20
Vertical Discharge Pipe Length
(= Disch. Pipe Height – X)
Locking Rail Length
( = Basin Depth – Y)
Guide Rail Length
(= Basin Depth – Z)
Cut Length of Base Pipe:
Minimum Basin Diameter (Simplex):
Minimum Basin Diameter (Duplex):
Vertical Discharge Pipe Length
(= Disch. Pipe Height – X)
Locking Rail Length
( = Basin Depth – Y)
Guide Rail Length
(= Basin Depth – Z)
Cut Length of Base Pipe:
Minimum Basin Diameter (Simplex):
Minimum Basin Diameter (Duplex):
Dimensional guide to be used only if upper bracket is
attached to cover as shown.
Thermal Leak
KW Sensor Sensor
1.5 No No
1.5 No No
1.5 No No
1.5 No No
1.5 Yes Yes
1.5 Yes Yes
1.5 Yes Yes
1.5 Yes Yes
2.2 Yes Yes
2.2 Yes Yes
3.0 Yes Yes
3.0 Yes Yes
5.6 Yes Yes
2
Vert. Disch.
Pipe Length
Locking Rail Length
Basin
Discharge
Depth
Height
X
Y
Dimension
Dimension
Winding Resistance in Ohms*
Insulation
Class B-W
B .90
F 2.2/8.8
B .90
F 2.2/8.8
B .90
F 2.2/8.8
B .90
F 2.2/8.8
B .36
F .74/2.96
B .36
F .74/2.96
F .54/2.16
Guide
Rail
Length
Z
2014 0995
SG12/SGC12
SG13/SGC13
X = 22-3/4" (58 cm)
Y =29-1/4" (74 cm)
Z = 19-3/8" (49 cm)
14" (36 cm)
24" (61 cm)
36" (91 cm)
SGC20
X = 25-7/16"(64.5cm)
Y = 26-3/4"(68 cm)
Z = 21-5/8"(55 cm)
16" (41 cm)
30" (76 cm)
42"(107 cm)
B-R R-W
5.3 6.2
2.2/8.8 2.2/8.8
5.3 6.2
2.2/8.8 2.2/8.8
5.3 6.2
2.2/8.8 2.2/8.8
5.3 6.2
2.2/8.8 2.2/8.8
1.9 2.26
.74/2.96 .74/2.96
1.9 2.26
.74/2.96 .74/2.96
.54/2.16 .54/2.16