National Flooring Equipment 7700 Series Operating Manual
All-day battery ride-on scraper
Hide thumbs
Also See for 7700 Series:
- Service manual (32 pages) ,
- Operating & service manual (44 pages)
Related Manuals for National Flooring Equipment 7700 Series
Summary of Contents for National Flooring Equipment 7700 Series
- Page 1 7700 ALL-DAY BATTERY RIDE-ON SCRAPER OPERATING MANUAL Read Manual Before Operating Machine 401836 Rev H...
- Page 2 TO PURCHASE THIS PRODUCT PLEASE CONTACT US Equipment Financing and Extended Warranties Available Discount-Equipment.com is your online resource for commercial and industrial quality parts and equipment sales. 561-964-4949 visit us on line @ www.discount-equipment.com Select an option below to find your Equipment We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto, Power Blanket, Nifty Lift, Atlas Copco, Chicago Pneumatic, Allmand, Miller Curber, Skyjack, Lull,...
-
Page 3: Table Of Contents
Table of Contents Table of Contents ................................3 Features and Specifications ............................4 Safety ....................................6 General Rules for Safe Operation ......................... 6 Ride-On Scraper Safety Guidelines ........................7 Hydraulic Safety ..............................8 Components and Assembly ............................9 Charger Instructions .............................. 9 Machine Charging .............................. -
Page 4: Features And Specifications
Features and Specifications Control Levers Adjustable Arm Rests Seat Switch Headlight DC Motor Pump Compartment Adjustable Slide Plate Adjustable Foot Rests 18” Wheels Cutting Head Onboard Battery Cylinder Lift Charger Forklift Cups Debris Deflector Swivel Cutting Head FEATURES Seat Switch - Ensures the machine will not function without someone DC Motor Pump Compartment - Provides easy access to the motor in the operator seat. - Page 5 Features and Specifications Machine Variants Region Serial Number Input Power Body Panels 7700-10XXXX 120V / 60 Hz Silver Vein Domestic 7700-12XXXX 120V / 60 Hz Green 7700-23XXXX 120V / 60 Hz Silver Vein 7700-11XXXX 230V / 50 Hz Silver Vein 7700-13XXXX 230V / 50 Hz Silver Vein...
-
Page 6: Safety
Read the manual carefully to learn equipment applications and limitations, as well as potential hazards associated with this type of equipment. Keep manual near machine at all times. If your manual is lost or damaged, contact National Flooring Equipment (NFE) for a replacement. Personal Maintenance &... -
Page 7: Ride-On Scraper Safety Guidelines
Safety RIDE-ON SCRAPER SAFETY GUIDELINES Scraping Charger Operation Do not drive machine along hills or uneven surfaces. Ensure proper use of charger. The weight of the machine may become distributed differently if on • Once connected and plugged into AC power, the LED will in- an uneven surface. -
Page 8: Hydraulic Safety
Safety HYDRAULIC SAFETY Maintaining a Safe Work Environment Establishing a safe work environment in and around your hydraulic equipment is extremely important. The easiest and most effective way to avoid problems is to make sure associates understand their equipment, know how to operate the machines safely, and recognize the dangers if handled carelessly. -
Page 9: Components And Assembly
Components and Assembly CHARGER INSTRUCTIONS See Ride-On Safety Guidelines for charger safety and instructions. Before making AC connections, refer to the requirements on the charger ID label. This battery charger must be grounded to reduce the risk of electric shock. Chargers are equipped with a grounding type plug. -
Page 10: Transport
Components and Assembly TRANSPORT • Secure machine with ratchet straps during transport. Proper securing straps need to be rated at least twice the weight of the machine. • Chock wheels to keep machine from rolling, but do not use them on their own. •... -
Page 11: Cutting Head And Blades
Components and Assembly Transport Wheels The front wheel assembly is included and very helpful when moving a machine around on a jobsite or loading a machine that is not on a pallet. It allows machine stability and safe transportation over most surfaces. It is quick and easy to attach or detach. Raise slide plate so the bottom of the slide plate is higher or even with the bottom of the guide channels, 6”-8”... - Page 12 Components and Assembly Swivel Head Blade Securing Bolt Cutting Head The swivel head keeps the blade in contact with the floor even when the floor is uneven. When using a flat blade, turning the head over 180° provides another sharp edge on the blade without having to replace the blade.
-
Page 13: Foot Pegs
Components and Assembly rower blades work easier than wider blades and usually clean the floor better. Wider is not always better or faster. Bevel Up • Normally, bevel on blade is up for concrete (Figure 9); bevel down for wood (Figure 9.1) •... -
Page 14: Operation
Operation OPERATING CONTROLS Power On Button/Key (Figure 12) Never use the Power On button/key as a method for speed control. Speed control is achieved by the hydraulic valve only. Using the On/Off switch repeatedly will cause excessive wear and premature failure of electrical components. Hydraulic Levers (Figure 13) International Domestic... -
Page 15: Shut-Down Procedure
Operation SHUT-DOWN PROCEDURE The machine will stop when the operator is no longer seated, or when the emergency stop is engaged. Remove blade or drop cutting head to the floor when machine is not in use. SLIDE PLATE ADJUSTMENTS AND SETTINGS Dual Lift (Figure 17) Prior to adjusting the dual lift hydraulic slide plate, make sure the channel guide is free of FIG. - Page 16 Operation Wood The slide plate should be adjusted to a low setting 1” (2.5 cm) off the floor. Use shank blades, shank blades with carbide tips, or a 6” or 8” (15-20 cm) cutting head with heavy duty blades. Note: Run machine 45° to the grain of the wood. Secondary Backing Carpet The slide plate should be adjusted to a low setting 1”...
-
Page 17: Ditching
Operation Wood Sub-Floor Tile Ditch 1’-2’ 2”-6” A heavy machine cannot be used on wood subfloors or raised panel computer floors. CROSS-ROOM DITCHING Strips Blade Keep machine light; remove all weights. A weighted machine could break through the floor. The slide plate should be adjusted to a low setting, 1” (2.5 cm) off the floor. Blades should be as flat of an angle as possible. -
Page 18: Maintenance Schedule
Maintenance Schedule Interval After initial After initial Maintenance to be performed Daily 200 hrs 1000 hrs 2000 hrs 100 hrs 500 hrs Inspect extension cord for damage ● Check wheels, caster and wheel motors for build up; and clean ● Inspect all safety devices (e-stop, backup beeper, seat switch) ●... -
Page 19: Troubleshooting Guide
Troubleshooting Guide Problem Cause Solution Machine will not start. Seat safety switch is disengaged. Ensure operator is seated. Emergency stop (E-Stop) switch is disen- Twist E-Stop so that it is in the “POWER ON” gaged. position. Circuit breaker is in the “OFF” position. Verify circuit breaker is in “ON”... -
Page 20: Warranty
TO PURCHASE THIS PRODUCT PLEASE CONTACT US Equipment Financing and Extended Warranties Available Discount-Equipment.com is your online resource for commercial and industrial quality parts and equipment sales. 561-964-4949 visit us on line @ www.discount-equipment.com Select an option below to find your Equipment We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto, Power Blanket, Nifty Lift, Atlas Copco, Chicago Pneumatic, Allmand, Miller Curber, Skyjack, Lull,...