Advertisement
Quick Links
Fixed Position Camera Dome
INSTALLATION & OPERATION
MANUAL
Vicon Industries Inc. does not warrant that the functions contained in this equipment
will meet your requirements or that the operation will be entirely error free or perform
precisely as described in the documentation. This system has not been designed to be
used in life-critical situations and must not be used for this purpose.
Copyright
2003 Vicon Industries Inc. All rights reserved. Product specifications subject to
change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TELEPHONE: 631-952-CCTV (2288) FACSIMILE: 631-951-CCTV (2288)
Vicon Part No. 8009-8136-00-00 Section 3 Rev. 1103
24-Hour Technical Support: 800-34-VICON (800-348-4266)
TOLL FREE: 800-645-9116 UK: +44(0) 1489-566300
XX136-00-00
Advertisement
Related Manuals for Vicon V3FD Series
Summary of Contents for Vicon V3FD Series
- Page 1 Copyright 2003 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788 TELEPHONE: 631-952-CCTV (2288) FACSIMILE: 631-951-CCTV (2288)
-
Page 2: Fcc Notice
• Reorient the receiving antenna. If you are not satisfied with a Vicon product or service, I would like • Relocate the equipment with respect to the receiver. to know. Your complete satisfaction is the mission of every Vicon •... -
Page 3: Table Of Contents
② Locations subjected to high level of humidity and dust. REFERENCE ....................EG-9 (Operating humidity range: max 85% {No condensation}) VICON STANDARD EQUIPMENT WARRANTY ..........EG-10 (Storage humidity range: max 95% {No condensation}) ③ Locations where there are large amounts of water vapor and steam. -
Page 4: Parts Description
PARTS DESCRIPTION • Exterior Inner cover • Camera body interior Camera body View angle Focus adjustment adjustment lever lever Camera Lens Line phase adjustment Dome cover volume Body cover Coaxial Power video cable input Video output terminal • Accessories connector for service monitor cable switch... -
Page 5: Installation & Adjustment
INSTALLATION & ADJUSTMENT Creating a Hole in the Ceiling or Wall Connecting the Cables Make two holes for the screws affixing the camera body, and one hole for the Please refer to the diagrams below. ① Connect the video cable from monitor to the equipped video cable. power and video cables. - Page 6 Attaching the Service Monitor Adjusting the View Angle,Focus and Iris When adjusting the camera direction, view angle and focus, use the included Use the lever to adjust the view angle and focus. service monitor cable by connecting to the video output connector View angle adjustment lever (Lock screw) •...
- Page 7 DIP Switch Set Up Set according to lighting conditions. Attention: DO NOT change “FIX” switch position from the factory setting. Do not change the switch position from the factory setting. Shutter speed to be fixed at 1/100. Flickerless (FL) Normal position Set to this position when a strong light is in the Back Light back ground.
- Page 8 Line Phase Adjustment Completing the Adjustment and Installation (24VAC 60Hz, Line Lock mode) ① Attach the body cover. ② Attach the dome cover. If necessary, turn the volume to adjust the line phase. DC Iris Level Adjustment Set according to lighting conditions. If necessary, turn the volume to adjust the DC iris level.
-
Page 9: Specifications
SPECIFICATIONS Model V3FD-2810 Color / High Resolution Focal Length 2.8-10mm Max.Aperture Ratio 1:1.2 F1.2-360(DC auto iris) Iris 105.8° 〜27.0° 78.2° 〜21.6° Angle of View 55.8° 〜16.2° TV System NTSC Scanning Syetem 2:1 Interlace Image Sensor 1/4" IT CCD Effective Elements 768 (H) ×... -
Page 10: Shipping Instructions
Vicon assumes no responsibility for poor performance when cables other than those recommended, or equivalent, are installed. In all cases, coaxial cable impedance should 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed be 75 ohms. -
Page 11: Vicon Standard Equipment Warranty
1. VCRs, all models: Labor and video heads warranted for 120 days from date of basis. Vicon does not warrant that such software shall be error (bug) free. Soft- original retail purchase. All other parts warranted for one year from date of origi- ware support via telephone, if provided at no cost, may be discontinued at any nal retail purchase. - Page 12 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) &Infofax: 800-287-1207 Atlanta Office Vicon Europe Headquarters 3070AA Business Park Drive Brunel Way Norcross, Georgia 30071 Fareham, PO15 5TX 770-449-0499 800-824-8479 United Kingdom...
Need help?
Do you have a question about the V3FD Series and is the answer not in the manual?
Questions and answers