Table of Contents
Advertisement
Quick Links
XX211-21
Quick Guide for
V15CCM-IR-2 Series Corner-Mounted
High-Security Cell Cameras
Copyright © 2010 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice
Vicon and its logo are registered trademarks of Vicon Industries Inc.
Perspex is a registered trademark of Perspex South Africa (Pty).
Resistorx is a registered trademark of Acument Global Technologies.
Dyna-Poxy is a trademark of Pecora Corporation.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-2288
FAX: 631-951-2288
TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44 (0) 1489 566300
WEB: www.vicon-security.com
Vicon part number 8009-8211-21-00
Rev 1210
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vicon V15CCM-IR-2 Series Rouchneck
Summary of Contents for Vicon V15CCM-IR-2 Series Rouchneck
- Page 1 Copyright © 2010 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice Vicon and its logo are registered trademarks of Vicon Industries Inc. Perspex is a registered trademark of Perspex South Africa (Pty). Resistorx is a registered trademark of Acument Global Technologies.
-
Page 3: Fcc Notice
FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception. -
Page 4: Important Safeguards - Indoor Use
The product shows a significant change in performance. 2. Retain Instructions - Retain all safety and operating 19. Replacement Parts - Use only Vicon specified replacement instructions for future reference. parts or an approved equivalent to prevent unit damage and 3. - Page 5 Introduction The information in this manual provides quick installation and maintenance procedures for the V15CCM-IR-2 Series of High-Security Corner-Mounted Cell Cameras. These units should only be installed by a qualified technician using approved materials in conformance with federal, state, and local codes. Read these instructions thoroughly before beginning an installation.
-
Page 6: Quick Install
Quick Install Below is an overview for installing the V15CCM-IR-2 camera. When using rear cover, refer to the diagram that follows. Figure 1 Installation Diagram 2 • Quick Install XX211-21 Rev 1210 V15CCM-IR-2 Series High-Security Cell Cameras... - Page 7 When using rear panel, follow diagram below. Quick Install • 3 XX211-21 Rev 1210 V15CCM-IR-2 Series High-Security Cell Cameras...
-
Page 8: Installation
5. When the camera mounting frame is secured to the surface, apply an epoxy security sealant around the perimeter of the base plate where it meets the ceiling/wall. [Vicon recommends DynaPoxy™ EP1200 (US) or Arbokol 1025 (UK) or equivalent for this purpose.] Installation with the rear cover: Note: The installation corner must be sharp and clean;... -
Page 9: Cable Connections
7. When the camera mounting frame assembly is secured to the surface, apply an epoxy security sealant around the perimeter of the base plate assembly where it meets the ceiling/wall. [Vicon recommends DynaPoxy™ EP1200 (US) or Arbokol 1025 (UK) or equivalent for this purpose.] Cable Connections All cabling is done to the boards located on the back of the front plate. -
Page 10: Final Installation
Final Installation When all connections are made, secure the front plate to the base plate using the security screws previously removed using no. 20 Torx bit. Camera/Lens Positioning and Adjustments The camera is on an adjustable mount so that it can be tilted slightly up and down to give a precise view. The wide angle 2.5 mm lens enables the camera to view the area with no “blind spots.”... -
Page 11: Osd Menu Map
OSD Menu Map 1. E X P OS URE 6. P RIV A CY LENS MASK 1 E. SHUTTER MASK 2 MASK 3 MAX_DR MASK 4 MASK 5 SENSE_UP MASK 6 2. COLOR 7. S Y NC WB MODE SYNC MODE R-Y GAIN V_PHASE B-Y GAIN... -
Page 12: Vicon Standard Equipment Warranty
Vicon Security Management Systems (SMS) All Models: All hardware is warranted for two years from date of original retail purchase. 10. Any product sold as “special” or not listed in Vicon’s commercial price list: One year from date of original retail purchase. - Page 13 Notes Vicon Standard Equipment Warranty • 9 XX211-21 Rev 1210 V15CCM-IR-2 Series High-Security Cell Cameras...
-
Page 14: Corporate Headquarters
Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-2288 800-645-9116 Fax: 631-951-2288 Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Vicon Germany Kornstieg 3 D-24537 Neumuenster...
Need help?
Do you have a question about the V15CCM-IR-2 Series Rouchneck and is the answer not in the manual?
Questions and answers