Related Manuals for Yetter NARROW ROW
Summary of Contents for Yetter NARROW ROW
- Page 1 NARROW ROW RESIDUE MANAGER OPERATOR’S MANUAL PART IDENTIFICATION 2565-694_REV_F 07/2021 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com...
-
Page 2: Forward
Important will WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. -
Page 3: Safety Information
SAFETY A brief description of signal words that may be used in this manual: CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices. WARNING: Denotes a specific potential hazard. DANGER: Denotes the most serious specific potential hazard. SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. -
Page 4: Table Of Contents
TABLE OF CONTENTS Forward…..…………………………………………………………………..……2 Warranty……………………………….……………………………………..……2 Safety Information………………………………………………….……….. Bolt Torque…………………………………………………………..……….. Installation Instructions………………………………………………… ..…..6-7 Operation……………………………...……………………………….…….. Maintenance……………………………………………………………... …. 9 Parts Identification………………………………..………….…….….. ….. 10-15... -
Page 5: Bolt Torque
BOLT TORQUE Mounting bolts and hardware Before operating the Residue Manager for the first time, check to be sure that all hardware is tight. Check all hardware again after approximately 50 hours of operation and at the beginning of each planting season. All hardware used on the Residue Manager is Grade 5 unless otherwise noted. -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS 2967 – RESIDUE MANAGER STEP 1. Build half of the row cleaner wheel assemblies as left hand wheel assemblies and half as right hand wheel assemblies. This is determined by which side of the wheel support and in which hole the wheel assembly is installed. - Page 7 INSTALLATION INSTRUCTIONS STEP 3. The universal model that fits on JD 7200/1700 series planters can be mounted two ways (See Figure 1). The front set of holes is to mount these models on planter units with light duty or heavy duty cast lower parallel arms.
-
Page 8: Operation
OPERATION The 2967 Residue Manager is designed to work in heavy residue situations especially where minimum soil movement is required. Depending on conditions and objectives, the 2967 Residue Manager can be set shallow with the teeth only engaged in the residue so as to clear heavy residue with minimal soil disturbance. -
Page 9: Maintenance
Clean machine thoroughly to remove all dirt, debris and crop residue, which would hold moisture and cause rusting. Inspect machine for worn or broken parts. See your Yetter Farm Equipment dealer during the off-season so that parts or service can be acquired when machine is not needed in the field. -
Page 10: Parts Identification
PARTS IDENTIFICATION PARTS IDENTIFICATION 2967-036A CASE 800/900/950/955/1200 WILL NOT FIT 1 YEAR IH PRODUCTION 800 (1981) - Page 11 PARTS IDENTIFICATION 2967-048A...
- Page 12 PARTS IDENTIFICATION 13” TAPER TOOTH SPOKE WHEEL 2966-117 (SHOWN) 2966-116...
- Page 13 PARTS IDENTIFICATION 13” BEVEL WHEEL 2966-117-BW (SHOWN) 2966-116-BW...
- Page 14 PARTS IDENTIFICATION 13” SHARK TOOTH WHEEL 2966-117-ST (SHOWN) 2966-116-ST...
- Page 15 PARTS IDENTIFICATION 2967-195 – RESIDUE MANAGER BRACKET ASSEMBLY...
- Page 16 2565-694_REV_F • 07/2021...