Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Yetter Manuals
  4. Farm Equipment
  5. 2968-020B
  6. Set-up / parts manual

Yetter 2968-020B Set-Up / Parts Manual

Row unit mid-mount fertilizer injection opener john deere, kinze, harvest international, & white row units
Hide thumbs

Advertisement

Quick Links

Download this manual
ROW UNIT MID-MOUNT FERTILIZER INJECTION OPENER
John Deere, Kinze, Harvest International, & White Row Units
2968-020B, 2968-021B, 2968-022B, 2968-025B, 2968-026A, & 2968-027A
2968-040A, 2968-041A, 2968-042A, 2968-043A, 2968-044A, & 2968-045A
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website: www.yetterco.com
E-mail:
info@yetterco.com
GERMINATE UNIFORMITY ™
SINGLE WHEEL MODELS
DUAL WHEEL MODELS
SET UP & PARTS MANUAL
2565-951_REV_C – 01/2020

Advertisement

loading

Related Manuals for Yetter 2968-020B

Summary of Contents for Yetter 2968-020B

  • Page 1 ROW UNIT MID-MOUNT FERTILIZER INJECTION OPENER John Deere, Kinze, Harvest International, & White Row Units SINGLE WHEEL MODELS 2968-020B, 2968-021B, 2968-022B, 2968-025B, 2968-026A, & 2968-027A DUAL WHEEL MODELS 2968-040A, 2968-041A, 2968-042A, 2968-043A, 2968-044A, & 2968-045A SET UP & PARTS MANUAL 2565-951_REV_C –...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS FOREWORD …………………………………………………...….…....3 SAFETY …………………………………………………………...…....4 PICTORIAL PART LIST …………………………………....5 – 12 INSTALLATION …………………………………………………..…..13 – 20 OPERATION ..………………..…………………......21 – 22 MAINTENANCE ……………………………..………....23 – 25 PARTS IDENTIFICATION………………………………...….... 26 – 45 TROUBLESHOOTING ...............46 BOLT TORQUE Important: Over-tightening hardware can cause just as much damage as under-tightening.

  • Page 3: Foreword

    WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. This warranty does not obligate the Company to bear cost of labor in replacement of parts.

  • Page 4: Safety

    BE ALERT! YOUR SAFETY IS INVOLVED WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION – BE ALERT!” It is your responsibility as an owner, operator, or supervision to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations.

  • Page 5: Pictorial Part List

    2968-020B Pictorial Parts List For JD 1700, 7200, & 7300 Single Disc, Left or Right Hand 2968-153 Only if –LH Ordered Only if –RH Ordered 2968-361 2968-222 QTY 1 2968-470-LH QTY 1 2968-470-RH QTY 1 QTY 1 QTY 1 Bolt Bag Short Fert.
  • Page 6 2968-027A Pictorial Parts List For Kinze 4900 Single Disc, Left or Right Hand 2968-156 2968-228 Only if –LH Ordered Only if –RH Ordered 2968-361 QTY 1 QTY 1 QTY 1 2968-470-LH QTY 1 2968-470-RH QTY 1 Bolt Bag Close Wheel Mount Arm Clamp Short Fert.
  • Page 7 2968-044A Pictorial Parts List For Harvest International, Dual Disc 2968-361 2968-225 2968-157 QTY 1 QTY 1 QTY 1 2968-470-RH QTY 1 2968-471-LH QTY 1 Arm Clamp Bolt Bag Close Wheel Mount Short Fert. Wheel Mount, RH Tall Fert. Wheel Mount 2968-045A Pictorial Parts List For Kinze 4900, Dual Disc 2968-158...
  • Page 8 2526-253 - 3/8 FLAT WASHER ZP – QTY 2 2968-218 - INJECTOR HOLDER W.A. – QTY 2 2968-153 Pictorial Parts List – Bolt Bag for 2968-020B & 2968-026A 2502-104 -1/4-20 X 1/2 HHCS GR 5 ZYD – QTY 2 2502-293 – ½ - 13 X 1 ¼ HHCS GR 5 ZYD– QTY 2 2502-351 -1/2-13 X 2 HHCS GR 5 ZP–...
  • Page 9 2968-154 Pictorial Parts List – Bolt Bag for 2968-021B 2502-104 -1/4-20 X 1/2 HHCS GR 5 ZYD – QTY 1 2502-232 – 3/8-16 X 1 ½ HHCS GR 5 ZP – QTY – 1 2502-245 - 3/8-16 X 1 ¾ HHCS GR 5 ZP – QTY 1 2502-351 -1/2-13 X 2 HHCS GR.5 ZP–...
  • Page 10 2968-156 Pictorial Parts List – Bolt Bag for 2968-027A 2502-104 – 1/4-20 X 1/2 HHCS GR 5 ZYD – QTY 1 2502-266 – 7/16-14 X 1 ½ HHCS GR 5 ZYD – QTY 1 2502-351 – ½ -13 X 2 HHCS GR 5 ZP– QTY 3 2502-368 -1/2-13 X 5-1/2 HHCS GR5 ZP –...
  • Page 11 2968-158 Pictorial Parts List – Bolt Bag for 2968-045A 2502-104 – 1/4-20 X 1/2 HHCS GR 5 ZYD – QTY 2 2502-266 – 7/16 – 14 X 1 ½ HHCS GR 5 ZP – QTY 1 2502-314 -1/2-13 X 2 ¼” GRADE 5 HHCS – QTY 3 2502-368 -1/2-13 X 5-1/2 HHCS GR5 ZP –...
  • Page 12 2968-159 Pictorial Parts List – Bolt Bag for 2968-041A CONT’D 2526-454 - 5/8 SAE FLATWASHER HRD'ND ZP – QTY 1 2570-724 - 3/8 HOSE P-CLIP W/ VINYL CUSHION – QTY 1 2968-363 - HOSE HOLDER, FORMED – QTY 1 2968-370 – GAUGE WHEEL ARM STOP – QTY 1 2968-373 –...

  • Page 13: Installation

    INSTALLATION INSTRUCTIONS Step 1: Remove OEM Tail Piece Remove the V-Closing Wheel Tail Piece from the row unit. JD 1700/7200/7300 Kinze/JD 7000/7100 Harvest International White 8000 White 9000...
  • Page 14 INSTALLATION INSTRUCTIONS Step 2: Fertilizer Mount Plate Installation Install Fertilizer Mount Plate for the Yetter 2968 unit where the closing wheel tail piece was originally assembled. JD 1700/7200/7300 JD 7000/7100/Kinze 2000 & 3000 Harvest International Kinze 4900 White 8000 White 9000...
  • Page 15 INSTALLATION INSTRUCTIONS Step 3: Attach Closing Wheel Assembly to Fertilizer Mount Plate Attach V-Closing Wheel Tail Piece to the Fertilizer Mount Plate. Reattach the spring. JD 1700/7200/7300 Kinze/JD 7000/7100 Harvest International White 8000 White 9000...
  • Page 16 INSTALLATION INSTRUCTIONS (2968-020A, 2968-021A, 2968-026A, & 2968-027A MODELS, SINGLE DISC) (IF INSTALLING 2968-040, 2968-041, 2968-044, OR 2968-045 DUAL DISC, SKIP TO 4B) Fertilizer Wheel Mount Assembly, Single Step 4A: Install the 2968-470-LH or 2968-470-RH Short Fert. Wheel Mount, Arm Clamp, & Formed Hose Holder to the Fertilizer Mount Plate using 3) ½”...
  • Page 17 INSTALLATION INSTRUCTIONS (2968-040A, 2968-041A, 2968-042A, 2968-043A, 2968-044A, & 2968-045 MODELS, DUAL DISC) Step 4B: Fertilizer Wheel Mount Assembly, Dual Install the 2968-359-RH L-Mount bracket, 2968-360 Tall L-Mount Bracket, Arm Clamp, & Formed Hose Holder to Fertilizer Mount Plate using 3) ½” X 2 ¼” Bolts & 3) ½” Lock Washers. NOTE: DO NOT tighten the 3) ½”...
  • Page 18 INSTALLATION INSTRUCTIONS Step 5: Fertilizer Wheel Assembly Place 1) 5/8” flat washer over the D-bolt & install the Fertilizer Wheel Assembly to Fertilizer Wheel Mount Plate & tighten 5/8” flange whiz lock nut. See page 21 to determine which D-bolt hole to install the wheel assembly to achieve your desired depth. SINGLE WHEEL (LH Shown) DUAL WHEEL Step 6: Set the Fertilizer Wheel Assembly Width...
  • Page 19 INSTALLATION INSTRUCTIONS STEP 7: P-Clip Installation Install each P-Clip to the Formed Hose Holder using ¼” X ½” bolts, ¼” lock washers, & ¼” hex nuts. A P-Clip should be placed on the side with blade for single wheel placement & on both sides for dual wheel placement. SINGLE WHEEL (LEFT SIDE SHOWN) DUAL WHEEL STEP 8A: INJECTOR INSTALLATION...
  • Page 20 INSTALLATION INSTRUCTIONS STEP 8B: REAR KNIFE INSTALLATION Assemble the 3/8 Hose P Clip to the horizontally slotted hole by placing the P Clip over the bolt threads, insert the 3/8” bolt thru the slotted hole, place a 3/8” flat washer & 3/8” lock washer over the bolt, & install a 3/8 hex nut. Insert 1) 3/8” X 3” bolt thru the stop bushing &...

  • Page 21: Operation

    OPERATION - On dual fertilizer placement, the wheels are staggered front to back to keep the soil from heaving. - Fertilizer can be placed 2” – 3” off the seed furrow. Please see your agronomist to determine best spacing on the rate that’s being applied.
  • Page 22 OPERATION LIQUID FERTILIZER APPLICATION RATE & PRESSURE CHART – TABLES BASED ON 30” NOZZLE SPACING GALLONS PER ACRE (USING WATER) TIP # LIQUID CAPACITY 1 NOZZLE 4 MPH 5 MPH 5.5 MPH 6 MPH 7 MPH 8MPH PRESSURE IN PSI IN GPM #00015 0.11...

  • Page 23: Maintenance

    MAINTENANCE IMPORTANT: If seal is removed from hub/bearing assembly, grease bearing Every 50 hours. If seal is left assembled, 2-3 pumps of grease twice a year, depending on acres, is sufficient to make sure the hub cavity is full. IMPORTANT: For proper operation, the planter frame must operate level (fore, aft &...
  • Page 24 MAINTENANCE NOTE: BE CERTAIN TO ALIGN THE GREASE FITTING WITH THE SLOT IN THE WHEEL & HUBCAP SO THAT THE GREASE CAN FLOW FREELY. Grease must fill this Hubcap cavity.
  • Page 25 Alternative Lubricants Conditions in certain geographical areas may require special lubricants & lubrication practices which do not appear in the operator’s manual. If there are any questions, consult Yetter Manufacturing Co. to obtain latest information & recommendation. PART #...
  • Page 26 2968-020B-L-LB PARTS IDENTIFICATION FOR JD 1700, 7200, & 7300 ITEM PART # DESCRIPTION 2502-104 ¼ - 20 X ½ HHCS GR 5 ZYD 2502-351 ½ - 13 X 2 HHCS GR 5 ZP 2502-379 M12 X 1.75 X 35 GRD 10.9 ZYD 2520-151 ¼...
  • Page 27 2968-020B-R-LB PARTS IDENTIFICATION FOR JD 1700, 7200, & 7300 ITEM PART # DESCRIPTION 2502-104 ¼ - 20 X ½ HHCS GR 5 ZYD 2502-351 ½ - 13 X 2 HHCS GR 5 ZP 2502-379 M12 X 1.75 X 35 GRD 10.9 ZYD 2520-151 ¼...
  • Page 28 2526-352 ½ SAE FLAT WASHER ZP 2526-402 9/16ID X 1 ¾OD X 1/4MB ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-223 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP...
  • Page 29 2526-352 ½ SAE FLAT WASHER ZP 2526-402 9/16ID X 1 ¾OD X 1/4MB ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-223 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP...
  • Page 30 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-355 ½ FLAT WASHER HARDENED ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-224 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-334 SPRING ANCHOR TAB 2968-361...
  • Page 31 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-355 ½ FLAT WASHER HARDENED ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-224 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-334 SPRING ANCHOR TAB 2968-361...
  • Page 32 5/8 – 11 WHIZ LOCK HEX NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-220 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 33 5/8 – 11 WHIZ LOCK HEX NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-220 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 34 5/8 – 11 WHIZ LOCK HEX NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-225 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 35 5/8 – 11 WHIZ LOCK HEX NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-225 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 36 ¾ - 10 HEX JAM NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-228 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 37 ¾ - 10 HEX JAM NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-228 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 38 5/8 – 11 WHIZ LOCK HEX NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-222 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 39 2526-352 ½ SAE FLAT WASHER ZP 2526-402 9/16ID X 1 ¾OD X 1/4MB ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-223 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP...
  • Page 40 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-355 ½ FLAT WASHER HARDENED ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-224 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-334 SPRING ANCHOR MOUNT TAB...
  • Page 41 5/8 – 11 WHIZ LOCK HEX NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-220 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 42 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-225 FERTILIZER CLOSE WHEEL MOUNT W.A., HARVEST INTL 2968-361 ARM CLAMP...
  • Page 43 ¾ - 10 HEX JAM NUT, GR 2, ZP 2525-151 ¼ MEDIUM LOCK WASHER ZP 2525-352 ½ MEDIUM LOCK WASHER ZP 2526-454 5/8 SAE FLAT WASHER HARDENED ZP 2565-179 YETTER DECAL 2570-724 3/8 HOSE P-CLIP WITH VINYL CUSHION 2968-228 FERTILIZER CLOSE WHEEL MOUNT W.A. 2968-361 ARM CLAMP 2968-363...
  • Page 44 2968-090A-L PARTS IDENTIFICATION ITEM PART # DESCRIPTION 2502-244 3/8 – 16 X 1 ¼ HHCS GR 5 ZP 2502-251 3/8 – 16 X 3 HHCS GR 8 ZP 2520-251 3/8 – 16 HEX NUT ZP 2525-251 3/8 MEDIUM LOCK WASHER ZP 2526-253 3/8 SAE FLAT WASHER ZP 2570-727...

  • Page 45: Parts Identification

    2968-091 PART IDENTIFICATION ITEM PART # DESCRIPTION 2515-846 MALE CONNECTOR – 3/8 X ¼ NPTF 2520-253 3/8 – 16 JAM HEX NUT ZP 2525-251 3/8 MEDIUM LOCK WASHER ZP 2526-253 3/8 SAE FLAT WASHER ZP 2968-218 INJECTOR HOLDER 2968-132 (SHOWN) 10” WHEEL ASSEMBLY & 2968-133 11” WHEEL ASSEMBLY PARTS IDENTIFICATION ITEM PART #...

  • Page 46: Troubleshooting

    TROUBLESHOOTING ISSUE CAUSE SOLUTION 2968 UNITS - PLANTER UNITS AREN’T EQUIPPED WITH ROW CLEANERS - ADD ROW CLEANERS TO PLANTER UNITS PLUGGING WITH - ROW CLEANERS AREN’T SET AGGRESSIVE ENOUGH - ADJUST ROWS TO CLEAR MORE TRASH FROM THE ROW RESIDUE - KNIFE (IF EQUIPPED) DRAGGING RESIDUE - ADJUST KNIFE POSITION HIGHER...
  • Page 48 2565-951_REV_C – 01/2020...

This manual is also suitable for:

2968-025b2968-021b2968-026a2968-022b2968-027a2968-040a ... Show all