Summary of Contents for Panduit Atlona Omega AT-OME-RX21
Page 1
4K/UHD Scaler for HDBaseT and HDMI Atlona Manuals AT-OME-RX21 Scaler / Receiver...
Page 2
Version Information Version Release Date Notes Sept 2019 Release AT-OME-RX21...
Page 3
Welcome to Atlona! Thank you for purchasing this Atlona product. We hope you enjoy it and will take a extra few moments to register your new purchase. Registration only takes a few minutes and protects this product against theft or loss. In addition, you will receive notifications of product updates and firmware.
Page 4
Atlona, Inc. (“Atlona”) Limited Product Warranty Coverage Atlona warrants its products will substantially perform to their published specifications and will be free from defects in materials and workmanship under normal use, conditions and service. Under its Limited Product Warranty, Atlona, at its sole discretion, will either: •...
Page 5
Atlona, Inc. (“Atlona”) Limited Product Warranty • Damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Atlona to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product.
Page 6
Important Safety Information 9. Do not defeat the safety purpose of a polarized CAUTION or grounding-type plug. A polarized plug has two RISK OF ELECTRIC SHOCK blades with one wider than the other. A grounding DO NOT OPEN type plug has two blades and a third grounding CAUTION: TO REDUCT THE RISK OF prong.
Introduction The Atlona AT-OME-RX21 is an HDBaseT receiver and 4K/UHD scaler with a local HDMI input. Part of the Omega™ Series of integration products for modern AV communications and collaboration, the OME-RX21 receives HDBaseT for video up to 4K/60 4:2:0, plus embedded audio, control, and Ethernet over distances up to 330 feet (100 meters). The HDMI input supports video up to 4K/60 4:4:4.
Panel Description AT-OME-RX21 LINK OMEGA OMEGA DEVICE IP INPUT PATTERN HDMI IN AT-OME-RX21 IP MODE C1 COM C2 HDBaseT IN OUTPUT RESET RS-232 RELAY DC 24V PWR LED HDBaseT IN Illuminates green when receiving power. Connect a compatible HDBaseT transmitter to this port.
Installation Captive Screw Connections RS-232 A 5-pin captive screw connector has been included for RS-232. NOTE: Port 1 will control the display and port 2 is for unit control. Pin out will be determined by the RS-232 cable and connect as RX (receive), TX (transmit) and (Ground).
Installation Mounting Instructions The AT-OME-RX21 includes two mounting brackets and four mounting screws, which can be used to attach the units to any flat surface. 1. Remove the top 2 case screws on the side of the unit. 2. Align the mounting brackets to the side of the units. 3.
Installation Cable Recommendation Guidelines Refer to the tables below for recommended cabling when using Altona products with HDBaseT. The green bars indicate the signal quality when using each type of cable. Higher-quality signals are represented by more bars. CAT5e CAT6 CAT6a CAT7 Core...
Installation IP Modes DHCP By default, the AT-OME-RX21 is set to DHCP mode. In this mode, when the AT-OME-RX21 is connected to the Local Area Network (LAN), it will automatically be assigned an IP address by the DHCP server (if available). Press the DEVICE IP button to show the IP address in the top left corner of the display.
WebGUI The AT-OME-RX21 includes a built-in webGUI, which allows easy remote management and control of all features. Follow the instructions below to access the webGUI. 1. Make sure that an Ethernet cable is connected between the LAN port on the AT-OME-RX21 and the network. 2.
webGUI Video Settings Select Video from the top navigation to adjust routing and video settings. Prefer Timing HDBaseT/HDMI - Select the source resolution to be passed. Options are: Native, 1280x800, 1920x1080, 1024x768, 1280x720, 1920x1200, 1366x768, 800x600, 1600x900, 2560x1440, 3840x2160, and 1440x900. Na- tive will allow the EDID handshake to determine the correct resolution for the source.
Page 16
webGUI Output Input Selection - Use the drop down menu to switch between A/V Mute (no signal), HDMI, HDBaseT, internal pattern 1, internal pattern 2, and internal pattern 3 source signals. Scaler - When enabled, will display extra options. This is for the HDMI output only. Output Resolution - Select the output resolution the source signal will be scaled to from the drop down menu.
webGUI Audio Select Audio from the top navigation to adjust volume, mute status, and EQ levels. Output Audio HDMI / L/R Enable - Unmutes the audio output signal, allowing audio to pass through the outputs. HDMI / L/R Disable - Mutes the audio output signal of the ports. No audio will pass when selected. NOTE: HDMI muting will mute the audio embedded on the HDMI output and L/R muting will mute the audio on the analog audio output.
webGUI Display Select Display from the top navigation to adjust display control settings. Command: Power - Press to send the CEC power on or off command out through the HDMI port. Command: Volume - Press to send the CEC Volume up, down, or mute commands through the HDMI port. System Settings Display Auto Power - Sets the unit to send the display power on/off command to the output.
Page 19
webGUI TCP/IP Settings of Controlled Device (only available when IP is selected) IP Mode - Toggle telnet login mode between Non-Login and Login. If set to Login, a username and password will be required to control the controlled device via TCP/IP. IP Address - Sets to the IP of the controlled device/display.
Page 20
webGUI RS-232 Select RS-232 from the top navigation to adjust the zone control parameters for the RS-232 port. RS-232 Parameter Setting RX RS232 1 - Select the baud rate, data bit, parity, and stop bit to match the RX21’s parameters. Defaults are 9600, 8, None, and 1.
webGUI EDID Select EDID from the top navigation to save/load EDIDs. EDID EDID Settings - Use the drop down menu to select from default (highest common resolution between source and display), 4 internal EDIDs, and 1 previously saved EDID. EDID Saved - The ID field will display the memory # and currently saved EDID name, select output 1 from the drop down menu.
webGUI System Select System from the top navigation to adjust relay, network, or system options. Relay Control - Set the relay to either follow the display’s status (on: c1-close c2-open, off: c1-open c2-close) or be manually set using the selectors in the webGUI. Relay - When the relay is set to manual, select the sliders to open and close the com ports.
Page 23
webGUI Network MAC Address - Displays the MAC address of the unit. IP Mode - Switch between static and DHCP IP modes. IP, Netmask, Gateway - This will display the unit’s current DHCP IP settings. When set to static, fill in the IP address, netmask, and gateway.
webGUI HDBT Select HDBT to open the HDBaseT cable test page. This page will check extender versions, cable status and length, and Video Quality. HDBT Test HDBaseT Zone - Use the drop down menu to select which HDBaseT input is being tested. Only active connections can be tested.