Table of Contents
Advertisement
Quick Links
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118
www.jasoninternational.com
MADE IN THE U.S.A.
INSTALLATION, OPERATION AND MAINTENANCE
If the carton shows sign of damage,
inspect the product before accepting
and describe the problem on the Bill of
Lading.
INSPECTION
Inspect the unit prior to installation. In the event of a
problem, DO NOT install the unit.
All components are factory assembled to the bath and the
unit is water tested and inspected prior to leaving Jason
International, Inc.
NOTE: Transportation and insurance from Jason's
factory are the buyer's responsibility.
Damage sustained in transit is the responsibility of the
carrier. If damage is discovered, the carrier must be
immediately notified in writing with a request for a
representative to inspect the unit. Failure of the carrier to
respond should be reported to the seller and carrier.
Always file a freight claim promptly.
The installer is responsible for insuring that the unit is free
from defects or shipping damage. In the event of a
problem, DO NOT install the unit.
Jason International is not responsible for damage that
might have been avoided by inspection or testing prior to
installation.
Damage to the unit during installation will not be covered
by warranty and is the responsibility of the installer.
·
Jason International, Inc.
™
Excel
501.771.4477
Collection Baths
ALL WARRANTY CLAIMS ON ACRYLIC SURFACE
DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
Inspect plumbing and bath surface for missing or damaged
components. Alert your dealer of any discrepancies.
To protect the unit from damage keep the bath in the
carton until ready for installation.
EQUIPMENT ACCESS
In accordance with Building Codes, service access to all
hydrotherapy bath equipment, controls and electrical
connections must be provided during installation
(Recommended minimum 28" x 17" [71 x 43 cm]).
Insufficient access will hinder repair and maintenance.
Warranty service will not cover costs of providing
equipment access.
Jason offers an optional removable lateral skirt for all
rectangular baths. The skirts are available in matching
acrylic colors and provide convenient access to bath
equipment, as well as an excellent finished appearance.
The Specification Sheet for this bath contains additional
technical information. This sheet can be provided by your
dealer or accessed online at
Page 1 of 12
www.excelbyjason.com
Customer Service: 800.255.5766
Copyright © 2021 Jason International, Inc.
49-1018-002
Date 05/2021
.
Advertisement
Table of Contents
Related Manuals for JASON Hydrotherapy Excel Series
Summary of Contents for JASON Hydrotherapy Excel Series
- Page 1 Jason International, Inc. 49-1018-002 8328 MacArthur Drive Date 05/2021 North Little Rock, AR 72118 www.jasoninternational.com MADE IN THE U.S.A. ™ Excel Collection Baths INSTALLATION, OPERATION AND MAINTENANCE If the carton shows sign of damage, ALL WARRANTY CLAIMS ON ACRYLIC SURFACE inspect the product before accepting DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. This manual contains information and instructions for proper operation and maintenance of your therapy bath. Failure to follow these instructions could result in personal injury, electrical shock, or fire. WARNING: When using this unit, basic precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY DANGER:... -
Page 3: Consignes De Sécurité Importantes
CONSIGNES DE SÉCURITÉ IMPORTANTES INSTRUCTIONS RELATIVES AU RISQUE DE FEU, CHOC ÉLECTRIQUE, OU DE BLESSURE. Ce manuel contient des informations et des instructions pour le bon fonctionnement et l'entretien de votre bain thérapeutique. Ne pas suivre ces instructions cela pourrait entraîner des blessures corporelles, un choc électrique ou un incendie. AVERTISSEMENT: Lors de l'utilisation de cet appareil, des précautions de base doivent toujours être suivies, y compris les suivantes: LIRE ET SUIVRE TOUTES LES INSTRUCTIONS ATTENTIVEMENT... - Page 4 Cautionary Warnings (English/French) CAUTION: Ambient temperature under the bath where ATTENTION: la temperature ambiante sous la baignoire equipment is installed must not exceed 122°F (50°C). où l'équipement est installé ne doit pas dépasser 50°C. WARNING: Any modification to the equipment is not AVERTISSEMENT : Toute modification de l'équipement recommended and will void the Manufacturer’s n’est pas recommandé...
- Page 5 FEATURES, CONTROLS AND OPERATING INSTRUCTIONS INTRODUCTION WHIRLPOOL FEATURES Whirlpool Pump This manual contains all of the information needed for Whirlpool pumps provided on Jason baths are factory the proper installation and operation for your Excel™ tested after installation on the bath. The pumps are of bath.
- Page 6 FEATURES, CONTROLS AND OPERATING INSTRUCTIONS (cont.) AIR FEATURES REMOTE MOUNTING OF AIR BLOWER ® The Jason AirMasseur system has been factory ® AirMasseur Blower installed following ETL/UL Standard safety guidelines. The blower generates warm air and pushes it through During installation, if remote mounting of the air blower the strategically placed air jets.
-
Page 7: User Maintenance Instructions
USER MAINTENANCE INSTRUCTIONS HUMIDITY SURFACE MAINTENANCE Area with minor scratches or dull surfaces can be restored WARNING: Avoid high humidity levels in your by applying commercially available plastic polish (i.e. home. Mold, mildew, fungi and bacteria which may Novus Plastic Polish No. 2, available at your Jason be harmful to health thrive in areas with continued dealer), followed by an application of acrylic paste wax. -
Page 8: Installation Instructions
INSTALLATION INSTRUCTIONS ® 2. AirMasseur Ventilation (AM baths) INSTALLATION A minimum ventilation opening of 2” x 4” [5x10cm] for 1. Finish Frame the AirMasseur blower is required. It should be designed to draw in indoor ambient air at a minimum of A finish frame under the shell rim should always be 72°F [22°C]. - Page 9 INSTALLATION INSTRUCTIONS (cont.) 5. Integral Tile Lip Alcove Installation 8. Cleaning After the bath has been leveled, confirm the height Remove all loose debris. Construction plaster or excess measurement of the underside of the flange deck in grout can be removed with the use of a wood (edge) order to install a 1”x2”...
- Page 10 INSTALLATION INSTRUCTIONS (cont.) ELECTRICAL INSTALLATION These instructions are written assuming 60Hz, 120V The pumps are supplied with an electrical bonding lug to power supply. Verify the electrical requirements of the allow connection of a solid copper bonding conductor bath unit before installation. Refer to the equipment between the unit and other electrical equipment and labels for voltage and frequency requirements.
-
Page 11: Troubleshooting Guide
TROUBLE SHOOTING GUIDE If you believe the unit to be within the warranty period, you must contact Jason Customer Service: 1-800-255-5766 with the bath’s Product and Serial numbers before work is started. These numbers can be found on the label on the front page of this manual and also adhered to the underside of the bath above the equipment. - Page 12 TROUBLE SHOOTING GUIDE WHIRLPOOL [WP] PUMP SYSTEM SYMPTOMS POSSIBLE CAUSES RECOMMENDED ACTION Pump operates, but no air is a) Air intake clogged. a) Refer to installer/dealer. injected into the water. a) Suction or discharge blocked. a) Check and remove obstruction Pump operates, but water is not being pumped.