Table of Contents
Advertisement
Quick Links
"TO BE REMOVED FOR USE BY THE OCCUPANT."
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118
www.jasoninternational.com
forma
InsTallaTIOn, OPeraTIOn, anD MaInTenanCe
If the carton shows sign of damage, inspect
the product before accepting and describe the
problem on the Bill of lading.
INSPECTION
Inspect the unit prior to installation. In the event of a
problem, DO NOT install the unit.
All components are factory assembled to the bath and the
unit is water tested and inspected prior to leaving Jason
International, Inc.
If the carton shows sign of damage, inspect the product
before accepting and describe the problem on the Bill of
Lading.
NOTE: Transportation and insurance from Jason's
factory are the buyer's responsibility.
Damage sustained in transit is the responsibility of
the carrier. If damage is discovered, the carrier must
be immediately notified in writing with a request for a
representative to inspect the unit. Failure of the carrier
to respond should be reported to the seller and carrier.
Always file a freight claim promptly.
Owner's reCOrD
Dealer:
Date Purchased:
Date Installed:
Installer:
Jason International, Inc. • 501.771.4477
Owner's Manual
Microsilk™-whirlpool Baths
®
Page 1 of 18
The installer is responsible for insuring that the unit is
free from defects or shipping damage. In the event of a
problem, DO NOT install the unit.
Jason International is not responsible for damage that
might have been avoided by inspection or testing prior to
installation.
Damage to the unit during installation will not be covered
by warranty and is the responsibility of the installer.
ALL WARRANTY CLAIMS ON ACRYLIC SURFACE
DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
Inspect plumbing and bath surface for missing or damaged
components. Alert your dealer of any discrepancies.
To protect the unit from damage keep the bath in the
carton until ready for installation.
PlaCe serIal nuMBer CarD wITh
PrODuCT COnfIguraTIOn In ThIs BOx
49-1011-700
Date 03/11
Customer Service : 800.255.5766
Copyright © 2011 Jason International.
Advertisement
Table of Contents
Related Manuals for JASON Hydrotherapy forma AC553
Summary of Contents for JASON Hydrotherapy forma AC553
- Page 1 “TO BE REMOVED FOR USE BY THE OCCUPANT.” Jason International, Inc. 49-1011-700 8328 MacArthur Drive Date 03/11 North Little Rock, AR 72118 www.jasoninternational.com Owner’s Manual forma Microsilk™-whirlpool Baths ® InsTallaTIOn, OPeraTIOn, anD MaInTenanCe If the carton shows sign of damage, inspect The installer is responsible for insuring that the unit is free from defects or shipping damage.
-
Page 2: Installation Instructions
INSTALLATION INSTRUCTIONS EqUIPMENT ACCESS In accordance with Building Codes, service access to all Jason offers an optional removable lateral skirt for all rect- therapy bath equipment, controls and electrical connections angular baths. The skirts are available in matching acrylic must be provided during installation (see Table 1 – Speci- colors and provide convenient access to bath equipment fications for minimum access size). - Page 3 INSTALLATION INSTRUCTIONS (cont.) Jason offers a removable lateral skirt for most baths. The INSTALLATION skirts are available in matching acrylic colors and provide convenient access to bath equipment as well as an ex- Each bath is provided with a cardboard bath well protector cellent finished appearance.
- Page 4 INSTALLATION INSTRUCTIONS (cont.) NOTE: Do not install the MicroSilk™ Pump Assembly Mortar is required when the subfloor is not smooth and further than the length of the tubing that is factory level; when additional sound insulation is desired; or when installed on the bath.
- Page 5 INSTALLATION INSTRUCTIONS (cont.) Figure 6 6. Clamp the MicroSilk™ Suction Line to the MicroSilk™ Suction Barb using the clamp provided on the tubing. Assure the MicroSilk™ Suction Line will allow proper drainage to the suction (See Figure 8). The suction hose must have a continuous drop from the suction barb to the suction fitting.
- Page 6 INSTALLATION INSTRUCTIONS (cont.) eLeCTRICAL product. ELECTRICAL POWER SUPPLY: These instructions are NOTE: In the Commonwealth of Massachusetts, written assuming 60Hz, 120v (or 240v for Signature Edition) installation is to be done by a Massachusetts licensed power supply. Special notations are also included for the plumber.
- Page 7 INSTALLATION INSTRUCTIONS (cont.) box bracket so that the two boxes can communicate a dedicated 240v 20A, 50 Hz, GFCI protected circuit and the pump control must be plugged into another dedicated properly through their infrared communication feature. 240v, 20A, 50 Hz, GFCI protected circuit. (See Figure During installation, the control box bracket and controls must be positioned horizontally and located to permit access for inspection and servicing.
- Page 8 INSTALLATION INSTRUCTIONS (cont.) CLeANINg WATeR TeSTINg Before finishing the installation, it is recommended that the Remove all loose debris. Construction plaster or excess bath be water tested and the plumbing tested for leaks. grout can be removed with the use of a wood (edge) trowel.
- Page 9 MICROSILK -WhIRLPOOL CONTROL bOX CONNeCTIONS STANDARD eDITION MICROSILK -WhIRLPOOL Jason’s Standard Edition MicroSilk-Whirlpool system fea- STANDARD eDITION MICROSILK-WhIRLPOOL tures the best in luxury bathing for the leisure bath industry. PARTS LIST To assure that your bath functions properly, the MicroSilk and pump control boxes must be properly connected.
- Page 10 CONTROL bOX CONNeCTIONS (cont.) Figure 11 PReMIeR eDITION MICROSILK-WhIRLPOOL PARTS LIST MicroSilk Pump Unit MicroSilk Control Box Pump Pump Control Box Control Box Stand Water Level/Vacuum Sensor Keypad Keypad Cable LED Light Assembly LED Light Cable Ozone Sanitation Unit NOTE: This diagram (Figure 11) also applies to 50 hz, 240v pumps, controls, and power supply systems.
- Page 11 OPeRATINg INSTRUCTION, FeATUReS, AND CONTROLS INTRODUCTION 1 1/2-HP, 3 speed pump; Automatic 1.5kW Heater, Chromatherapy mood light, Automatic Ozone System that This manual contains all of the information needed for the will be operated any time the pump is powered; a digital proper installation and operation of your Jason MicroSilk- control with LCD display window;...
-
Page 12: Filling And Draining
OPeRATINg INSTRUCTIONS, FeATUReS, AND CONTROLS (cont.) MicroSilk Unit Filling and Draining Close the drain and fill the bath with water at least two (2) The MicroSilk generates oxygen rich microbubbles that fill inches (50mm) above the jets. The inlet temperature should the bath. - Page 13 STANDARD AND PReMIeR eDITION MICROSILK -WhIRLPOOL TOUChPAD Option MicroSilk On/Off Whirlpool On/Off LeD Light MICROSILK™-wHIRLPOOL T h e J a s o n S t a n d a r d a n d P r e m i e r E d i t i o n LeD Light Icon M i croSilk-W hir lp o ol tou c hpad is u se d to ac c es s...
-
Page 14: Menu Instructions
SIgNATURe eDITION MICROSILK -WhIRLPOOL TOUChPAD Whirlpool On/Off Pillow On/Off MicroSilk On/Off LeD Light LeD Light Icon T h e J a s o n S i g n a t u r e E d i t i o n M i c r o S i l k - Whirlpool digital touchpad is used to access all the Hold the key for less than two (2) seconds to turn the lights... -
Page 15: User Maintenance Instructions
USeR MAINTeNANCe INSTRUCTIONS hUMIDITy clean soft cloth. Do not use sandpaper, steel wool, or abrasive rubbing compounds. WARNING: AvOID hIGh hUMIDITY LEvELS IN YOUR hOME. MOLD, MILDEW, FUNGI AND BACTERIA WhICh If scratches are too deep to rub out, or if the damage penetrates MAY BE hARMFUL TO hEALTh ThRIvE IN AREAS WITh the acrylic surface, consult your dealer for recommendations CONTINUED hIGh hUMIDITY LEvELS;... -
Page 16: Troubleshooting Guide
TROUbLe ShOOTINg gUIDe If you believe the unit to be within the warranty period, you must contact Jason Customer Service: 1-800-255-5766 with the bath’s Product and Serial numbers before work is started. All warranty repairs must be authorized by Jason before work is started. FOR SERVICE, ALWAYS CONTACT YOUR DEALER OR AUTHORIZED SERVICE CENTER WARNING: Always turn off power at the main electrical service panel when servicing the bath. -
Page 17: Warranty
whIrlPOOl PuMP sYsTeM POssIBle Causes reCOMMenDeD aCTIOn sYMPTOMs a) Reset circuit breakers and check GFCI. Check fuses and a) No power to the pump unit. replace if bad. b) Pump motor is not plugged in. Pump system won’t start. b) Make sure plug is fully inserted into the ourlet. c) Insufficient water. -
Page 18: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS InsTruCTIOns PerTaInIng TO The rIsK Of fIre, eleCTrIC shOCK, Or InJurY TO PersOns. This manual contains information and instructions for proper operation and maintenance of your therapy bath. Failure to follow these instructions could result in personal injury, electrical shock, or fire. warnIng: when using this unit, basic precautions should always be followed, including the following: reaD anD fOllOw all InsTruCTIOns CarefullY...