Download
Share
Print this page
  1. Manuals
  2. Brands
  3. JASON Hydrotherapy Manuals
  4. Bathtubs
  5. Vivere Series
  6. Owner's manual

JASON Hydrotherapy Vivere Series Owner's Manual

Walk-in baths
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
"TO BE REMOVED FOR USE BY THE OCCUPANT."
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118
www.jasoninternational.com
MADE IN THE U.S.A.
INSTALLATION, OPERATION, AND MAINTENANCE
If the carton shows any sign of damage,
thoroughly inspect the product before accepting
and describe the problem on the Bill of Lading.
INSPECTION
Inspect the MicroSilk
®
Demonstration System prior to
installation. In the event of a problem, DO NOT install
the demonstration system.
All components are factory assembled to the system and
the system is water tested and inspected prior to leaving
Jason International, Inc.
NOTE: Transportation and insurance from Jason's
factory are the showroom's responsibility.
Damage sustained in transit is the responsibility of
the carrier. If damage is discovered, the carrier must
be immediately notified in writing with a request for a
representative to inspect the unit. Failure of the carrier
to respond should be reported to the seller and carrier.
Always file a freight claim promptly.
OWNER'S RECORD
Dealer:
Date Purchased:
Date Installed:
Installer:
Jason International, Inc. • 501.771.4477
OWNER'S MANUAL
Vivere
Collection Walk-In Baths
™
The installer is responsible for insuring that the unit is
free from defects or shipping damage. In the event of a
problem, DO NOT install the demonstration system.
Jason International is not responsible for damage that
might have been avoided by inspection or testing prior to
installation.
Damage to the unit during installation will not be covered
by warranty and is the responsibility of the installer.
ALL WARRANTY CLAIMS ON ACRYLIC SURFACE
DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
Inspect plumbing and bath surface for missing or damaged
components. Alert your dealer of any discrepancies.
To protect the unit from damage keep the bath in the
carton until ready for installation
PLACE SERIAL NUMBER CARD WITH
PRODUCT CONFIGURATION IN THIS BOX
Page 1 of 9
49-1016-001
Date 10/16
Customer Service : 800.255.5766
Copyright © 2016 Jason International.

Advertisement

loading

Related Manuals for JASON Hydrotherapy Vivere Series

Summary of Contents for JASON Hydrotherapy Vivere Series

  • Page 1 “TO BE REMOVED FOR USE BY THE OCCUPANT.” Jason International, Inc. 49-1016-001 8328 MacArthur Drive Date 10/16 North Little Rock, AR 72118 www.jasoninternational.com MADE IN THE U.S.A. OWNER’S MANUAL Vivere Collection Walk-In Baths ™ INSTALLATION, OPERATION, AND MAINTENANCE If the carton shows any sign of damage, The installer is responsible for insuring that the unit is free from defects or shipping damage.
  • Page 2 IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. This manual contains information and instructions for proper operation and maintenance of your therapy bath. Failure to follow these instructions could result in personal injury, electrical shock, or fire. WARNING: When using this unit, basic precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY DANGER:...
  • Page 3 CONSIGNES DE SÉCURITÉ IMPORTANTES INSTRUCTIONS RELATIVES AU RISQUE DE FEU, CHOC ÉLECTRIQUE, OU DE BLESSURE. Ce manuel contient des informations et des instructions pour le fonctionnement et l’entretien de votre bain de thérapie ap- propriée. Le non respect de ces instructions peut entraîner des blessures corporelles, de choc électrique ou d’incendie. AVERTISSEMENT: L ’...
  • Page 4 INSTALLATION INSTRUCTIONS (cont.) INSTALLATION PROCEDURES PRE-INSTALLATION PROCEDURES 1. Place the bath on a solid flat surface. Rotate the Place the bath on a flat surface in an area where it may be drained after testing. adjustable feet until all feet come in contact with the floor.

  • Page 5: Manufacturer's Warranty

    INSTALLATION INSTRUCTIONS (cont.) Figure 3 ELECTRICAL 2. GROUNDING IS REQUIRED. The unit should be installed by a qualified service representative and properly grounded. Electrical Power Supply: These instructions are written 3. INSTALL SERVICE CONNECTION AT LEAST 6” (15cm) assuming 60Hz, 120v power supply. Special notations are ABOVE SUB FLOOR.

  • Page 6: Water Testing

    INSTALLATION INSTRUCTIONS (cont.) Figure 4 EXTENSION PANEL INSTALLATION It is always preferable to protect the surface during installation to minimize cleanup and prevent surface damage. The Vivere Collection bath includes extension panels which WATER TESTING can be used as a filler panel to install the bath in a 60” (152 cm) opening.
  • Page 7 OPERATING INSTRUCTION, FEATURES, AND CONTROLS INTRODUCTION MICROSILK OPERATION All Jason MicroSilk baths are pre-plumbed at the factory This manual contains all of the information needed for the proper installation and operation of your Jason MicroSilk with standard equipment. Standard equipment includes a ®...
  • Page 8 OPERATING INSTRUCTION, FEATURES, AND CONTROLS DOOR SEAL LEAKING 6. Use disinfectant to clean any bathroom surfaces which are regularly exposed to moisture. If a small leak has been detected around door, check closely for any accumulation of dirt or debris. Any small collection 7.

  • Page 9: Troubleshooting Guide

    TROUBLE SHOOTING GUIDE If you believe the MicroSilk ® Demonstration system to be within the warranty period, you must contact Jason Customer Service: 1-800-255-5766 with the bath’s Product and Serial numbers before work is started. All warranty repairs must be authorized by Jason before work is started. FOR SERVICE, ALWAYS CONTACT YOUR DEALER OR AUTHORIZED SERVICE CENTER WARNING: Always turn off power at the main electrical service panel when servicing the bath.