Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eastwood 22979
Summary of Contents for Eastwood 22979
- Page 1 Item #22979 42" BELT & 6" DISC SANDER INSTRUCTIONS...
-
Page 2: Specifications
The EASTWOOD 42” BELT & 6” DISC SANDER is designed for rugged reliability and ease of use. The positionable belt drive assembly provides a full 90° of adjustment from horizontal to vertical and features a secure stop fence/tool rest for safety and convenience. The 6” disc sander features an angle-adjustable work surface and sliding miter gauge/fence to allow grinding to precise angles with one convenient bench mount tool. -
Page 3: Safety Information
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards. To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 4: Additional Safety Information
• This Sander will eject a trail of sparks at high speed which can ignite flammable materials or injure others nearby. Do not operate in the vicinity of flammable materials and keep all persons and pets away from the work area. Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com... - Page 5 Screw and Internal Tooth Lockwasher using the included 5mm Hex Key (FIG 3). • Peel off the backing to expose the adhesive, center and press the PSA Abrasive Disc [D] in place (FIG 4). FIG. 2 FIG. 3 Reverse Threaded FIG. 4 To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 6 Disc. Check for contact with Disc and adjust if necessary. • Slide the steel bar of the Disk Table Miter Gauge Assembly [G] into the groove of FIG. 6 the Disc Work Support Table. FIG. 7 0.63” [1.6 mm] Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
- Page 7 8mm Hex Key. FIG. 9 The Alternate Tool Rest [J] MUST NOT contact the Sanding Belt. Check for contact with Belt and adjust if necessary. """" 0.63” [1.6mm] FIG. 10 To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 8 Support Strut at the rear of the Belt Housing (FIG. 14). Be certain the Belt Sander assembly clamping is securely tight- ened. Severe personal injury could occur if Belt Sander Assembly position slips during use. FIG. 14 Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
-
Page 9: Operation
DO NOT force it into the disc (FIG 17). INJURY HAZARD! USE ONLY THE RIGHT or “ROTATING DOWN” SIDE of the Sanding Disc Face. Using the Left or “rotating Up” side may violently pull the workpiece from the hands. To order parts and supplies: 800.343.9353 >> eastwood.com... - Page 10 INJURY HAZARD! Unplug tool before beginning belt replacement or severe personal injury could result if motor should start during this procedure. Always use an Eastwood approved 2” x 42” sanding belt to insure safe operation. ABRASIVE BELT REMOVAL 1. Remove the Belt Work Support Table or Alternate Tool Rest (FIG 18).
-
Page 11: Abrasive Disc Replacement
Unplug tool before beginning disc replacement or severe personal injury could result if motor should start during this procedure. Always use an Eastwood approved 6” PSA sanding disc to insure safe operation. 1. Remove the Adjustable Disc Table/Miter Plate by loosening and removing the two knobs, one on each side. -
Page 12: Additional Items
If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: tech@eastwood.com PDF version of this manual is available at eastwood.com The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com © Copyright 2019 Eastwood Automotive Group LLC 4/20...