Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eastwood 32488
Summary of Contents for Eastwood 32488
- Page 1 Part #32488 VARIABLE SPEED 7"-9" SANDER/POLISHER INSTRUCTIONS...
-
Page 2: Specifications
The EASTWOOD VARIABLE SPEED 7-9” SANDER/POLISHER is built to high quality standards to provide long life and smooth operation to serve the demands of the avid hobbyist and seasoned professional alike. Features a soft-start trigger response to minimize polish spatter and an accurate, variable speed electronic speed control to help avoid paint surface damage or burn-through. -
Page 3: Safety Information
Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 4: Electrical Safety
Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards. Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com... -
Page 5: Additional Safety Information
• Never operate or store Sander/Polisher in damp or wet conditions. • Plug into a minimum 15 amp properly grounded circuit. If using an extension cord, it must be AWG 14 or greater, no longer than 25’. To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 6: Health Hazards
Do not resume use until resolution is found. • Always make sure the workpiece being sanded/buffed is securely clamped or anchored to allow two handed operation of the tool. Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com... - Page 7 Included Wool Bonnet etc.) for the job. • Plug into a minimum 15-amp, properly grounded circuit. If using an extension cord, it must be AWG 14 or greater, no longer than 25’. FIG. 4 To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 8 As a result, the following figures are only approximate: 1 = 1000 RPM 2 = 1500 RPM 3 = 2100 RPM 4 = 2400 RPM 5 = 2700 RPM 6 = 3000 RPM Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
- Page 9 NOTE: always start with the mildest pad and polish combination that will do the job and work toward the next mildest combination to achieve the best results with minimum work. The chart below will help determine the proper product combination for specific paint conditions. To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 10 - Minor clear coat scratches & abrasions. Polishing Compound - Water spots. 1200 to 1400 RPM - Surface haze. (Between 1 to 2 on Eastwood Sander/Polisher Dial) - Minor staining. Mild Foam Finessing Pads and Abrasive-free Wax or Polish - Swirl Removing.
- Page 11 SANDING/CLEANING By obtaining 7” hook and loop sanding and cleaning disks (Not Included), the Eastwood Sander/Polisher may be used for many sanding and surface cleaning jobs. • Set the Speed Control on the desired speed. The chart below will help determine the best setting for general conditions.
- Page 12 FIG. 8 (FIG 8). • Remove the spade connector at the end of the braided brush lead from the terminal by gripping with needle nose pliers and pulling outward (FIG 9). FIG. 9 Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
- Page 13 • Repeat above procedure for opposite brush. • Replace the Motor Brush Covers, replace the Motor Vent Panels and tighten screws. To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 14 NOTES Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
-
Page 15: Troubleshooting
Work only on 12:00 to 3:00 quadrant of pad at a Overheats Pad being ap- 10°-15° angle. plied to surface Dirt and debris buildup in motor Use a brush or compressed air to remove debris. cooling air slots To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 16: Additional Items
Microfiber Towel Set If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: tech@eastwood.com PDF version of this manual is available at eastwood.com The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com...