Rice Lake 880 Performance Series Operation Manual
Hide thumbs
Also See for 880 Performance Series:
- Technical manual addendum (123 pages) ,
- Technical manual & parts lists (122 pages) ,
- Technical and service manual (103 pages)
Subscribe to Our Youtube Channel
Related Manuals for Rice Lake 880 Performance Series
Summary of Contents for Rice Lake 880 Performance Series
- Page 1 880 Performance Series ™ Controller/Indicator Version 4.01 Operation Manual March 10, 2021 PN 152240 Rev D...
- Page 2 All information contained within this publication is, to the best of our knowledge, complete and accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make changes to the technology, features, specifications and design of the equipment without notice.
-
Page 3: Table Of Contents
Setup Menu ..........18 Technical training seminars are available through Rice Lake Weighing Systems. - Page 4 3.1 Error Messages ..........31 Compliance ................32 Specifications ................33 Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit www.ricelake.com/webinars. Visit our website...
-
Page 5: Introduction
Information contained within this manual is exclusively for units with CPU IMPORTANT board, PN 175109 (blue in color). The 880 Performance Series Technical Manual (PN 158387) is referred to in this manual is available online. Manuals and additional resources are available on the Rice Lake Weighing Systems website at www.ricelake.com... -
Page 6: Safety
General Safety Do not operate or work on this equipment unless this manual has been read and all instructions are understood. Contact any Rice Lake Weighing Systems dealer for replacement manuals. WARNING Failure to heed may result in serious injury or death. -
Page 7: Overview
• 179160 Indicator Option, Profinet Model 880 Indicator • 179161 Indicator Option, Modbus TCP Model 880 Indicator • 179162 Indicator Option, Devicenet Model 880 Indicator • 179163 Indicator Option, Profibus Model 880 Indicator © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 8: Operating Modes
• View or clear the accumulator value • Change setpoint values • View the current tare value • Enter Setup mode (if audit trail is enabled) rmation. 880 Performance Series Technical Manual (PN 158387) for more info Visit our website www.RiceLake.com... -
Page 9: Front Panel Display
Setup mode. The keys are used to navigate through menus, select digits within numeric values, and increment/decrement values. Gross Brutto ZERO TARE PRINT UNITS MENU GROSS Figure 1-1. 880 Front Panel Display (Universal Model) © Rice Lake Weighing Systems ● All Rights Reserved... - Page 10 880 Performance Series Controller/Indicator Item No. Function Sets the current gross weight to zero; Used to navigate to other menus or to select another digit when editing a value Sends an on-demand print format to a communications port, provided the conditions for standstill are met;...
-
Page 11: Menu Structures And Parameter Descriptions
Use the navigation keys to move the decimal point left or right. Press when done. TARE See the 880 Performance Series Technical Manual (PN 158387) for more information. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 12: Alphanumeric Entry Procedure
880 Performance Series Controller/Indicator 1.6.3 Alphanumeric Entry Procedure Use the following scheme for alphanumeric entry when using the five-button keypad. Level 1 Level 1 Parameter Parameter Level 2 Level 2 Parameter Parameter Display first 6 Scroll left in format string. -
Page 13: Indicator Operations
OIML mode). Display shifts to gross weight and the ZERO TARE Gross LED is lit. If keyed tares are allowed, press to open the keyed tare prompt. TARE Note To clear the tare, press again. TARE © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 14: Preset Tare (Keyed Tare)
880 Performance Series Controller/Indicator 1.7.6 Preset Tare (Keyed Tare) Note Tare mode must be set to keyed or both for the preset tare feature to function. 1. With the scale empty and zero weight on the display, press . 000000 displays TARE with the focused digit flashing. -
Page 15: Displaying Audit Trail Information
7. Select the type by pressing to desired setting then press to set the value. For complete list of settings see the 880 Performance Series Technical Manual (PN 158387) for more information. to return to Weigh mode. 8. When all settings have been made, press MENU Setpoints are now accessible from the front panel menu. -
Page 16: Display Or Edit Setpoint Value
880 Performance Series Controller/Indicator 1.7.11 Display or Edit Setpoint Value . Audit displays. 1. Press MENU until Setpts displays. 2. Press 3. Press and the first available setpoint number displays. 4. Press to toggle through each setpoint which is operator accessible. -
Page 17: Set Time And Date
PRINT The format of the print output can be configured using the accumulator print Note format. See the 880 Performance Series Technical Manual (PN 158387) for more information. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 18: Clear The Accumulator
Weigh mode. MENU If there is no tare in the system, the value displayed is zero and the Gross and Net LED turn off. See the 880 Performance Series Technical Manual (PN 158387) for more information. Visit our website www.RiceLake.com... -
Page 19: Configuration
When the indicator is placed in Configuration mode, SCALE displays. The SCALE menu is the first of eight top-level menus used for configuring the indicator. Detailed descriptions of these menus are given in the 880 Performance Series Technical Manual (PN 158387). When configuration is complete, return to the SCALE menu and press the (ZERO) key to exit Setup mode. -
Page 20: Configuration Methods
Configuration using the menus is described in the 880 Performance Series Technical Manual (PN 158387). Configuration using the EDP port can be accomplished using either the EDP command set described in the 880 Performance Series Technical Manual (PN 158387) or Version 3.0 or later of the Revolution configuration utility. -
Page 21: Front Panel Configuration
View, print or clear the current accumulator value, if enabled SETPTS Setpoints Configure setpoint values and Enable/Disable setpoints; Only configured setpoints are available TARE Tare View the current tare value Table 2-1. 880 Menu Summary © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 22: Menu Structures And Parameter Descriptions
880 Performance Series Controller/Indicator Menu Structures and Parameter Descriptions The following sections provide graphic representations of the 880 menu structures. In the actual menu structure, the settings chosen under each parameter are arranged horizontally. To save page space, menu settings display in vertical columns. The factory default setting display at the top of each column and is bold. -
Page 23: Scale Menu
ACCUM THRESH CALIBR 30HZ LIGHT 1-99999 BOTH 0-999999 Section 2.2.5 on page 21 MEDIUM DELAY 60HZ NOTARE HEAVY PBTARE 120HZ 240HZ KEYED 480HZ 960HZ 7.5HZ 15HZ Figure 2-5. Scale Menu Structure © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 24: Format Menu
880 Performance Series Controller/Indicator 2.2.4 Format Menu ..SETUP T & D INFO If SPLIT = OFF ..SCALE FEATUR PORTS ..FORMAT ZTRKBN ZRANGE DSPDIV UNITS DECPNT DSPDIV UNITS DECPNT 888888 88888.8 888880 888888 8.88888 888880 88.8888... -
Page 25: Calibration Menu
WGT 1 CAL1 Display and Previous A/D raw edit test counts are shown. weight value Press Enter to calibrate span Press menu to cancel Calibrating, please wait Figure 2-7. Calibration Menu Structure © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 26: Feature Menu
880 Performance Series Controller/Indicator 2.2.6 Feature Menu ..SETUP T & D INFO ..PORTS PFORMT FEATUR REGION CONSC# PASSWD Section 2.2.7 000000 CURVAL RESVAL USER SETUP on page 23 KEYLCK LATUDE ELEVAT IRITE LOCALE 0-90 -9999 to +9999... -
Page 27: Region Menu
PORTS PFORMT SETPTS USBCOM SERIAL FLDBUS ETHNET CHAN 1 CHAN 2 Section 2.2.9 on Section 2.2.10 Section 2.2.11 page 24 on page 25 on page 25 Figure 2-10. Ports Menu Structure © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 28: Com And Usbcom Menus
880 Performance Series Controller/Indicator 2.2.9 COM and USBCOM Menus ..SETUP T & D INFO ..PORTS PFORMT SETPTS ..USBCOM SERIAL ETHNET CHAN 2 CHAN 1 Same menu structure as COM with DUPLEX added. SFMT TRIGGE TERMIN... -
Page 29: Ethernet Communications Menu
2.2.11 USB Host and Fieldbus Menus ETHNET FLDBUS FORMAT SWAP DVCNET PRFBUS LOAD SAVE? AOPEXT WORD OLDSTD BOTH CFG ? AOPSTD NONE CAL ? BYTE ALL ? Figure 2-13. USB Host and Fieldbus Menu Structures © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 30: Print Format Menu
880 Performance Series Controller/Indicator 2.2.12 Print Format Menu ..SETUP T & D INFO ..PFORMT SETPTS DIGIO GFMT NFMT ACCFMT SPFMT HDRFMT format PORT format USBCOM CHAN 1 CHAN 2 ETH-S ETH-C USBMEM Figure 2-14. Print Format Menu Structure 2.2.13 Setpoint Menu... - Page 31 NOTE: x = maximum number of bits SLOT1 – If RELAY option board is installed. supported for the slot/card. SLOT 0 – If any DIGIO are configured as OUTPUT. Figure 2-16. Setpoint Menu Structure – Layout A © Rice Lake Weighing Systems ● All Rights Reserved...
- Page 32 880 Performance Series Controller/Indicator Setpoint Menu – Layout B PAUSE, DELAY, WAITSS, COUNTR, AUTJOG CLRACM CLRTAR PSHACM PSHPRT PSHTAR VALUE number ONQUIE WAITSS DELAY, WAITSS and AUTJOG setpoints only. ACCESS NAME SLOT DIGOUT SENSE BRANCH NONE 6ALPHA NORMAL BIT1-BITx SLOT 0...
-
Page 33: Digital Input/Output Menu
UNITS KBDLOC 24-channel card is installed CLEAR GROSS DSPACC DSPTAR PRIM NT/GRS CLRCN CLRTAR BATRUN CLARACC BATSTR OUTPUT BATPAS INPUT BATRST PROGIN Figure 2-19. Digital Input/Output Menu Structure © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 34: Analog Output Menu
880 Performance Series Controller/Indicator 2.2.15 Analog Output Menu The ALGOUT menu is used only if the analog output option is installed. If the analog output option is installed, configure all other indicator functions and calibrate the indicator before configuring the analog output. See Technical/Service Manual for analog output calibration procedures. -
Page 35: Troubleshooting
NO ZERO Zero is prevented (due to regulatory mode Check zero settings and for motion settings, motion on the scale, zero range settings) Table 3-1. Error Messages © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 36: Compliance
880 Performance Series Controller/Indicator Compliance DECLARATIONOF CONFORMITY 880 indicator series 2014/30/EU EMC EN 55011:2009+A1:2010, EN 61326-1:2006 2014/35/EU LVD IEC 60950-1 ed.2 2011/65/EU RoHS EN 50581:2012 __________________________ _____________ ________ __________________________ May 3, 2019 __________________________ __________________________ __________________________ Visit our website www.RiceLake.com... -
Page 37: Specifications
LED, 0.56'' (14 mm), six-digit, 14-segment with decimal or comma Keys/Buttons Membrane panel, tactile feel Temperature Range Certified 14°F to 104°F (-10°C to 40°C) Operating 14°F to 122°F (-10°C to 50°C) © Rice Lake Weighing Systems ● All Rights Reserved... - Page 38 880 Performance Series Controller/Indicator Dimensions (W x H x D) Panel 6'' x 4'' x 4.95'' (152 mm x 102 mm x 126 mm) Universal 9.87'' x 9.38'' x 4.33'' (251 mm x 238 mm x 110 mm) Weight Panel 2.5 lb (1.2 kg)
- Page 40 Specifications subject to change without notice. Rice Lake Weighing Systems is an ISO 9001 registered company. 230 W. Coleman St. • Rice Lake, WI 54868 • USA U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319...
Need help?
Do you have a question about the 880 Performance Series and is the answer not in the manual?
Questions and answers