Maintenance Of The Product - Prilux flexilight MAXIBRILLO Manual

LED
MAXIBRILLO
210713
210737
210744
210751
210768
60º
IP54
230V
-20º
BEFORE STARING THE INSTALLATION OF THIS PRODUCT , PLEASE READ ATTENTIVELY THE INSTRUCTIONS AND KEEP
THEM IN A SAFE PLACE.
THE INSTALLATION SHOULD BE PERFORMED BY QUALIFIED PERSONNEL.
THE IMPROPER HANDLING OF THE COMPONENTS OR THE PRODUCT COULD DAMMAGE THE CORRECT FUNCTIO-
NING OF THIS DEVICE THUS CANCELLING THE WARRANTY OF THE PRODUCER
THE WARRANTY OF THE PRODUCER IS CANCELLED IF THE INSTALLATION IS NOT PERFORMED FOLLOWING THE
INDICATED IN REBT 2002.
THE APPLICATION ITC BT09-4 OF THE REBT IS MANDATORY (INSTALLATION OF OVERVOLTAGE PROTECTORS OF IN
LINES AND RECEIVERS) FOR INDUSTRY INSTALLATIONS AND PUBLIC LIGHTING. THE WARRANTY DOES NOT COVER
DAMMAGES PRODUCED BY OVERVOLTAGE ON RECEIVERS WITHOUT OVERVOLTAGE PROTECTORS.
THE APPLICATION OF ITC BT19 ( INTERIOR OR RECEIVING INSTALLATIONS.GENERAL PRESCRIPTIONS) IS MANDA-
TORY.
THE APPLICATION OF ITC BT34 (INSTALLATIONS FOR SPECIAL PURPOSES. FAIRS AND STANDS) IS MANDATORY.
ALL PRILUX CHRISTMAS LIGHTING MOTIF, NEED A MAINTENANCE BEFORE BEING USED, IT MEANS TO CHECK ALL
THE CONNECTIONS (INCLUDED THE END CAP) IN ORDER TO BE SURE THAT THE MATERIAL HAS THE PERFECT TIGHT-
NESS.
SUMMARY
FLEXILIGHT LED is a new serie of product for a professional design.
You can decorate both indoors and outdoors from the buildings, highlighting
something, surroundings from a specified place, making a kind of symbol or
lighting windows, entrances, stairs, trailers, cars, etc. It all depends on the ima-
gination of each one.
WARNING: Avoid making inappropriate installations as well these ones which
are damaged, and please, we invite you to read carefully the following ins-
tructions manual to do a safe installation.
The product is supplied with power cable and end cap. The rest of accessories
are sold separately, for instance, heat shrink tubes, flanges, cable conduit, etc
CAUTIONS
• No use this product in contact with water or with wet hands.
• Never place or use this product close to heat sources (for instance:
heating).
• No connect this product while it remains rolled, it might set fire.
• Use only this product with enough ventilation and refrigeration.
• If you use this product outdoors, you must use as electrical outlet a IPX4
tigh-base.
• If you use this product outdoors, you must always use a Power Failure
Protection Switch (FI-30mA) between the Power Supplier (220-240V) and the
product.
• Protect all the cables against potential damages.
• The lamps are not exchangable.
• Under no circumstances should you beat this product with a hammer, it
might damage the lamps.
• If the product is mounted to hang freely, it must be adjusted to a steel
cable and be connected to it every 10 cm.
• If the luminous thread is going to use in permanent installations, you have
1/5
abril 2020
50m

MAINTENANCE OF THE PRODUCT

[GRÁFICOS: Unidades en mm/ GRAPHICS: Units in mm/GRAPHIQUES: Unités en mm/GRÁFICOS: Unidades em mm]
ACCESSORIES
Power cable (Incluided)
End cap
Junction
Conjector L
Attachment clip
WARNING
to take into account that it will lose progressively performance in white and
blue colors after many continuous hours.
CONNECTION TO THE POWER SUPPLIER
• Do not connect the luminous thread to the power supplier until the insta-
llation or the modification has been completed.
• Do not connect the luminous thread to the power supplier until the end
cap has been fixed with security to the edge of the luminous thread.
• Do not connect the garland to the power supplier while it is in its packa-
ge, unless the package has a decorative meaning.
• Make sure that the power supplier has not a higher voltage that the
luminous thread.
• It is recommended to use plug/ adapter with fuse in order to avoid any
damages from overload.
CONNECTION.
• Only can be connect between them those luminous thread with the
same voltage.
• When it is going to make connections between pieces from the luminous
thread, o the luminous thread with the power cord, make sure that both
parts keep the narrowest as possible.
• The connector pins and the copper wire of the luminous thread.
• The male and female connector.
• The length of the luminous thread has not to overcome the maximum
power load (Look the chart with the parametres)
• It is recommended to seal all the connectors with neutral adhesive silico-
ne in order to avoid the entry of moisture in the luminous thread.