Table of Contents
Advertisement
Quick Links
INSTALLATION CERTIFICATE
The undersigned qualified installer attests to have personally fitted the here described vehicle
security system following the manufacturer instructions.
By :
ALARM KIT
932MHW
932MHW
Type of device :
&
Sold on :
725W
SIREN
................................................
&
Siren 725W
Vehicle :
..........................................................................................................................
USER AND
INSTALLER MANUAL
UK
GEMINI Technologies S.r.l.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia
Tel. +39 0332 943211 - Fax +39 0332 948080
www.gemini-alarm.com
Rev.02 - 03/24
ISO 9001Certified Company
Made in Italy
Advertisement
Table of Contents
Related Manuals for Gemini 932MHW
Summary of Contents for Gemini 932MHW
- Page 1 & Siren 725W Vehicle : .......................... USER AND INSTALLER MANUAL GEMINI Technologies S.r.l. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia Tel. +39 0332 943211 - Fax +39 0332 948080 www.gemini-alarm.com Rev.02 - 03/24 ISO 9001Certified Company...
-
Page 2: Table Of Contents
2.2 - SYSTEM PARTIAL ARMING 9.2 - Passive arming......................PAGE 09 To arm the system without arming interior protection press button “ ” on the Gemini remote control. 9.3 - Door switch polarity selection................... PAGE 09 System arming is confirmed by a Bop (if acoustic signals are enabled). -
Page 3: Arming Delay
One alarm cycle lasts for 30 sec. 2.7 - SYSTEM DISARMING Press the unlock button on the vehicle original remote control or button “ ” on the Gemini remote control; disarming is confirmed by 2 Beeps (if acoustic signals are enabled). -
Page 4: Wireless Siren 725W
BLUE wire Optical signals activated by connection to the Hazard switch will ONLY turn For complete information regarding connections, please refer to your vehicle specific ON during an alarm condition wiring diagram (available diagrams can be downloaded from the restricted area of our website: www.gemini-alam.com). PAGE 07 PAGE 06... -
Page 5: Vehicle Code Programming
The system must be configured according to the specific vehicle model on which it is to be installed. The alarm system can work via CAN BUS (with the vehicle original remote control) and via the Gemini help you understand the coding procedure, here below is an example shows how to configure a remote control (P/N 738NW). - Page 6 10.0 - SYSTEM PROGRAMMING EXAMPLE 11.0 - PAIRING NEW DEVICES To carry out the operation successfully, make sure the required electrical connections Press the “ ” button to enable the features and the “ ” button to disable them. (bonnet switch and ignition) are properly connected. If there is no bonnet switch, ground the GREEN wire (20-pin connector, pos.
-
Page 7: Deleting Programmed Devices
This wireless inclination sensor which integrates a 2.45GHz radio transceiver is compatible with the To carry out the operation successfully, make sure the required electrical connections Gemini 933MHW and 932MHW security systems (see par. 11.0 “PAIRING NEW DEVICES”). (bonnet switch and ignition) are properly connected. -
Page 8: System Reset
• Turn ignition key ON; reset is confirmed by a Beep and the wailing of the siren for approx. 3 seconds. • Turn ignition key OFF. The LED will power OFF to confirm the end of the procedure. ________________________________________________________ 16.0 - TECHNICAL SPECIFICATIONS ________________________________________________________ 932MHW UNIT : Power supply 12Vdc ________________________________________________________ Current draw (system armed + LED flashing)
Need help?
Do you have a question about the 932MHW and is the answer not in the manual?
Questions and answers