Page 1
GRASS COLLECTION SYSTEM PRO 3 BAGGER PRO 3 BAGGER EVERRIDE WARRIOR EVERRIDE WARRIOR 54” AND 60” DECKS 54” AND 60” DECKS 2009 2009 MODEL #50031303-54” MODEL #50031304-60” OPERATOR’S MANUAL OPERATOR’S MANUAL MANUAL PART #: Q0393 MANUAL PART #: Q0393 ASSEMBLY ASSEMBLY OPERATION...
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating.
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later.
Remove and sort all parts for easy identification. Verify all parts against the list on page 5. If parts are missing, please contact PECO Inc. at (800) 438-5823. NOTE: Study all drawings and exploded views on pages 16 thru 19 before starting assembly.
Figure 2-2b 2-1 Continued... (2) 3/8”-16 x 1-1/4 HHCS (2) 3/8”-16 Nyloc Nut Removing The Rear Bumper Guard Remove the four existing nuts and hex bolts that fasten the rear bumper guard to the rear frame of the mower. Set aside. This guard will be used in the next step. See Figure 2-1c.
2-3 Lower Mount Clamp Bracket Installation Continued... Existing Slot Hole Pattern Rear Frame Guard Clamp Bracket Figure 2-4b Figure 2-3b (1) 3/8”-16 x 2-1/4” x 2-5/8” U-bolt (2) 3/8”-16 Nyloc Nut (4) 3/8”-16 x 1-1/4” HHCS Bolt Mount Plate 2-4 PTO Mount Plate Assembly Installation Place the PTO mount plate assembly P#(A0670) onto the right rear chassis of the mower, lining up the lower...
2-5 Universal PTO Installation 2-6 Belt Installation/Removal and Adjustment To mount the PTO assembly, insert the mount rod on the PTO assembly P#(A0623) into the mounting slots Remove the (4) 1/4”-20 x ½” P#(K0353) HHSTS from located on the PTO mount plate assembly P#(A0670). the belt guard located on the bottom of the PTO Next, tilt the PTO assembly forward and insert the PTO assembly as shown in Figure 2-6a and 2-6b.
2-6 Belt Installation/Removal and 2-8 PTO Handle Installation Adjustment Continued... Mount the PTO handle P#(A0626) to the PTO assembly using (3) 1/4”-20 x 3/4” HHCS P#(K1222) and (3) 1/4”-20 A62K Kevlar Belt nyloc nuts P#(K1128). Refer to Figure 2-8a and 2-8b. Figure 2-6d (3) 1/4”- 20 x 3/4”...
2-10 Impeller Blade Removal/Replacement 2-9 Blower Cone Installation Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially thread the bolts into each of the two tabs located on the WARNING blower housing. Place blower cone so the two tabs line up with the bolts then tighten completely.
2-11 Upper Frame Assembly Installation 2-12 Top Assembly To Upper Frame Assembly Installation NOTE: During this step, it is suggested that two people Align the pivot brackets of the top assembly P#(A0551) install the upper frame to the lower mount tube. to the pivot point on either side of the upper frame assembly.
Attach the (1) boot plate mount pin P#(B0284) with (1) 2-13 Inlet Installation 3/8”-16 x 3/4” HHCS bolt and (1) 3/8”-16 lock washer P#(K0048). Insert the boot plate mount pin into the With the top assembly P#(A0551) in the upright position, existing hole on the mower deck and fasten the boot insert the inlet P#(V1054) into the right hand hole in the plate to the mower deck using the handle grip screw bolt...
Page 13
Mounting Bracket to the Inside 2-15 Front Weight Assembly Cont... Bracket Mount to the Outside Figure 2-15e Locate the front frame bar of mower. On each side of the front frame there is a tab on each side with an existing oblong slot.
2-16 Length Of Hose Adjustment 2-18 Lower Hose To Blower Cone Installation The hoses in steps 2-17 and 2-18 must be cut to fit your machine. Do not cut the hoses until you have tried to fit Slide a upper hose clamp P#(J1000) over both ends of them on your machine.
2-20 Installation/Removal Of Figure 2-20b Plastic Top Collection Bags To install the bag onto the bag ring, first make sure the bag ring end caps are fastened to the bag ring. Place the seam openings of the bag onto the bag ring openings and turn the bag until the slot bracket in the bag ring is protruding from the opening in the bag (Figure 2-20a).
SECTION III 3-3 Disengagement Of The PTO Assembly OPERATING INSTRUCTIONS A. To disengage the PTO assembly, slide the 3-1 General Safety engagement handle out of the retaining slot and push the engagement handle away from the operator’s seat. Only qualified people familiar with this operator’s manual and the mower’s operator’s manual should operate this WARNING: The PTO assembly blades will continue to machine.
SAFETY DECALS To promote safe operation, PECO Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. P P P P P P P...