Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco 49120907
Summary of Contents for Peco 49120907
- Page 1 P P P P P P GRASS PECO PECO PECO PECO PECO COLLECTION SYSTEM Model# 49120907 Country Clipper MODEL YEAR: 2015-Newer Avenue 42”-54” & Boulevard 48”-54” OPERATOR’S MANUAL OPPERATION ASSEMBLY MAINTENANCE MANUAL PART#: Q0502 Rev. - 2.0...
-
Page 2: Table Of Contents
RESIDENTIAL BAGGING SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Boot To Mower Deck Installation - - - - - - - - - - - - - - 12 Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 Weight Kit Installation - - - - - - - - - - - - - - - - - - - - - -13 Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4... -
Page 3: Safety
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Rear Mount Plate Installation
See next page for assembly views Rear Mount Plate Installation Attach P#(B0898) Rear Mount Plate to the rear of the mower using (2) P#(K0286) U- Bolts and (4) P#(K2038) 3/8”-16 Ny-Flange Locknuts. B0898 Rear Fame Plate Mount Plate Brace Installation Next, attach the (2) Mount Plate Braces to the frame by first removing the existing 3/8”... - Page 6 Rear Mount Plate and Lower Mount Tube Assembly Item # Part # Desc. Qty. B0898 Rear Mount Plate K0286 U-Bolt 3/8"-16 x 3-1/2" IW x 3-1/8" ID B0899 Mount Plate Brace K1182 3/8"-16 x 1" Carriage Bolt K2038 3/8"-16 Ny-Flange Lock Nut B0640 Lower Mount Tube / 29"...
-
Page 7: Upper Frame Assembly Installation
Figure A Top Assembly To Upper Frame Upper Frame Assembly Installation Assembly Position the Top Assembly P#(A2101) above the Upper Hair Pin Frame Assembly as shown in Figure B. Fasten the Top Clip Assembly to the Upper Frame Assembly using (2) 5/16”- 18 x 2-1/2”... - Page 8 Item # Part # Desc. Qty. A1114 Upper Frame Assy. / Generic A2047 A2101 A1028 Top Assy / P2B+ / PECO V0019 Inlet V0025 ZT-0004 SWING ARM BRKT K0037 Flat Washer / 1/4" (.75 OD x .312 ID x .060 T) K2516 5/16"-18 Ny-Flange Lock Nut...
-
Page 9: Hinge Kit Assembly Installation
Hinge Kit Assembly Installation Assemble the Hinge Kit as shown in Figure A, using (2) 5/16”-18 x 1” HHCS P#(K1154), (3) 5/16”-18 Ny-Flange Locknuts P#(K2516), (5) 1/4” Flat Washers P#(K0037) and (2) Swing Arm Brackets P#(ZT-0004). Place (1) Vinyl Cap P#(J0289) on the end of the hex bolts as shown in Figure A. - Page 10 Attach Rubber Strap P#(J4009) to mower deck using (1) P#(K1025) 1/4”-20 Carriage Bolt. (1) P#(K0037) 1/4” Flat Washer and (1) P#(K2014) 1/4”-20 Ny-Flange Locknut. Open end of hook should be facing deck discharge. Attach Front Boot Plate P#(B0920) to outside of the Boot and the Boot Plate Fastener P#(B0922) on the inside using (2) P#(K1010) 1/4”-20 x 5/8”...
-
Page 11: Grass Deflector Adjustment
Grass Deflector Adjustment Flap Can Be Adjusted Up/Down Depending On Mowing Conditions. Adjust Flap Up To Allow More Dense Material To Reach Left Bag. Adjust Flap Down To Allow Less Dense Material To Reach The Right Bag. Once Adjusted Properly, Both Bags Should Fill Evenly, But May Require Further Adjusting When Mowing Conditions Change. - Page 12 Hose Installation Attach Hose to opening on Boot P#(V0049) and secure with P#(J0060) Hose Clamp. Stretch Hose to Inlet P#(V0025), attach and secure using P#(J0060) Hose Clamp. (Note: If excessive sagging occurs, shorten by cutting excess Hose and re-attach.) Hose Clamps...
-
Page 13: Weight Kit Installation
Weight Kit Installation Item # Part # Desc. Qty. B0741 5-1/2" Weight Bar B0834 Weight Brkt. Clamp B0900 Weight Bracket K1182 3/8"-16 x 1" Carriage Bolt K1624 3/8" x 6-1/8" Clevis Pin K0086 Hair Pin Clip .125 OD x 2.50 K2038 3/8"-16 Ny-Flange Lock Nut Attach (1) P#(B0900) Weight Bracket to... -
Page 14: Installation/Removal Of Collection Bags
Installation/Removal Of Collection Figure C Plastic Top Bags IMPORTANT! To prevent bag wear, install (2) red plastic end caps P#(J0274), as shown in Figure A, on each bag ring before installing bags. Bag Ring Figure A Red Plastic End Caps Fasten Draw Completed Bag -Latch Here... -
Page 15: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R1051 Warning: Hearing Protection Label... -
Page 18: Notes
Unit Model Number:_______________________________________________ Unit Engine Size:__________________________________________________ Unit Serial Number:________________________________________________ Date of purchase:________/________/_________ Dealer/Distributor Name:__________________________________________ Address: _________________________________ State:_______ Zip:_______ Phone Number: ____________________________________________________ New PECO, Inc. 10 Walden Dr Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com... - Page 19 Notes:...
- Page 20 P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...