IMPORTANT SAFETY INFORMATION GENERAL SAFETY PRECAUTIONS The following precautions are an integral and essential part of the product and must be supplied to the user; Read them carefully as they contain important indications for the safe installation, use and maintenance. 1.
GENERAL SAFETY INFORMATION An appliance shall be provided with an instruction manual. The instruction manual shall give instructions for the installation, operation, and user maintenance of the appliance. The installation instructions shall specify the need for a grounding-type receptacle for connection to the supply and shall stress the importance of proper grounding.
Page 4
The installer shall follow the provided instructions thoroughly. SEA products must only be used to automate doors, gates and wings. Any initiative taken without SEA USA Inc. explicit authorization will preserve the manufacturer from whatsoever responsibility.
Page 5
NOTES: 1. The same type of device shall not be used for both entrapment protection means. Use of a single device to cover both the opening and closing directions is in accordance with the requirement; however, a single device is not required to cover both directions.
Page 6
PRICES: Prices are based on the Price List in force. Discounts and quotation from Sales Rep. and other selling branches must be approved by SEA. Prices are F.O.B SEA Warehouse in Miami and do not include shipments costs. SEA reserves the right to modify the price list at any time and provide notice to its sales network.
In case of leaves longer than 13,12 feet or installations in windy places or in case of closed panelled gates, SEA recommends the use of the electric lock on operators without block (SB) ; moreover, the exclusion of electronic slowdown is recommended in case of operators with hydraulic slowdown AIN COMPONENTS 1.
Page 8
FULL TANK 20 - 40 Fig. 5 Oil fill in cover THE SPHERIC JOINT IS STANDARD ON ALL Oscillating fork Breather screw SUPER FULL TANK SUPER FULL TANK 20 SUPER FULL TANK 40 SUPER FULL TANK 20 TECHNICAL FEATURES G6 120V G4 120V G6 380V Power supply...
Page 9
INWARD OPENING INSTALLATION NOTES INWARD INSTALLATION « » 1,57 inches DIMENSION HAS BEEN CALCULATED FOR A outside THICK GATE ** T « » DIMENSIONS HAS BEEN CALCULATED ON A MINIMUM 2,87 inches 6,42 inches, AND A MAXIMUM OF SPACED EVERY 31,18 INCHES LWAYS INSTALL THE OPERATOR INSIDE THE PROPERTY...
INSTALLATION ON MASONRY PILLARS BY MAKING A RECESS CAUTION! During installation, make sure that the connection cables do not interfere 70,87 with the recess (SUPER NOTES 2,56 FULL TANK 20) 1 - dimensions in inches 6,89 Minimum 110,24 In case you need to (SUPER make a recess, observe FULL...
Page 11
INSTALLATION OF THE OSCILLATING FORK ON THE REAR BRACKET Fig. 14 Fig. 15 - Mount the oscillating fork on the rear bracket, then secure the fixing pin as shown in Fig. 14 DO NOT use the hammer to insert the short brass pin; its fitting into the fork and the bracket must be get by the simple pressure of the hands DO NOT incline the hydraulic operator further than the oscillating fork allowed angle (1), it may cause its breaking (Fig.
Page 12
INSTALLATION OF THE OPERATOR ON THE FRONT BRACKET 1) Place the operator shaft in the housing of the front bracket 2) Secure the shaft to the front bracket by tightening the screw (Fig. 22) Fig. 22 Fig. 21 INSTALLATION OF THE CHROME PLATED SHAFT COVER Fig.
EXTERNAL RELEASE MOUNTING NOTE 1 - Remove the transporting plate 2 - Mount the release The release key is kept in a special housing inside the release lid Fig. 28 Fig. 27 BREATHER SCREW WARNING: It is obligatory to remove the breather screw at the end of the installation Unscrew and take off the end of...
Page 14
10) Check the functionality of all the accessories especially the function of all safety Annual devices and of the Linear Encoder Annual Lubricate the shaft with SEA grease (GREASE GL 00 Code 65000009) After the maintenance it is neccessary to repeat all tests before restarting the automation...
THE MANUFACTURER CAN NOT BE DEEMED RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED BY IMPROPER USE OF THIS PRODUCT SEA reserves the right to make all the necessary changes and modifications of the products or manuals without giving prior notice...
Page 16
SEA USA Inc. 10850 N.W. 21st - unit 160 - DORAL - MIAMI Florida (FL) 33172 Phone: ++1-305.594.1151 Toll Free: 800.689.4716 www.sea-usa.com sales@sea-usa.com...
Need help?
Do you have a question about the SUPER FULL TANK 20 G6 380V and is the answer not in the manual?
Questions and answers