SEA SURF 350 Manual
Electromechanical swing gate operator
Hide thumbs
Also See for SURF 350:
- Installation manual (24 pages) ,
- Manual (21 pages) ,
- Manual (20 pages)
Table of Contents
Related Manuals for SEA SURF 350
Summary of Contents for SEA SURF 350
- Page 1 SURF 350 - SURF 450 SURF K ELECTROMECHANICAL SWING GATE OPERATOR SEA USA Inc. 10850 N.W. 21st - unit 160 - DORAL - MIAMI Florida (FL) 33172 Phone: ++1-305.594.1151 Toll Free: 800.689.4716 www.sea-usa.com 67410720 REV 06 - 10/2020...
-
Page 2: Turning On The Power
IMPORTANT SAFETY INFORMATION GENERAL SAFETY PRECAUTIONS The following precautions are an integral and essential part of the product and must be supplied to the user; Read them carefully as they contain important indications for the safe installation, use and maintenance. 1. -
Page 3: General Safety Information
GENERAL SAFETY INFORMATION An appliance shall be provided with an instruction manual. The instruction manual shall give instructions for the installation, operation, and user maintenance of the appliance. The installation instructions shall specify the need for a grounding-type receptacle for connection to the supply and shall stress the importance of proper grounding. - Page 4 The installer shall follow the provided instructions thoroughly. SEA products must only be used to automate doors, gates and wings. Any initiative taken without SEA USA Inc. explicit authorization will preserve the manufacturer from whatsoever responsibility.
- Page 5 NOTES: 1. The same type of device shall not be used for both entrapment protection means. Use of a single device to cover both the opening and closing directions is in accordance with the requirement; however, a single device is not required to cover both directions.
- Page 6 PRICES: Prices are based on the Price List in force. Discounts and quotation from Sales Rep. and other selling branches must be approved by SEA. Prices are F.O.B SEA Warehouse in Miami and do not include shipments costs. SEA reserves the right to modify the price list at any time and provide notice to its sales network.
-
Page 7: Technical Specifications
TECHNICAL SPECIFICATIONS SURF (350 - 450) is an irreversible electromechanical swing gate operator strong and safe, easy to install, for leaf length up to 14,76 feet. SURF operator is equipped with release system through key, which allows the manual release of the leaf in case of emergency or black out 1. -
Page 8: Technical Data
TECHNICAL DATA SURF 450 24V SURF 450 24V FAST SURF K 24V TECHNICAL DATA SURF 350 24V Power supply 24Vcc Max. power 120 W 60 W Max. absorbed current 2,5 A 3,5 A 2350 rpm 3300 rpm Motor speed 15,75 inches... -
Page 9: Main Parts
USING GRAPHICS 16 feet Weight 15 feet 1200 Lb 13 feet 1100 Lb 12 feet 9 feet 1000 Lb 900 Lb 700 Lb OPERATOR 600 Lb SURF (120V) 400 Lb 5 ft 9 ft 15 ft 16 ft 12 ft 13 ft Leaf length Fig. -
Page 10: Standard Installation
STANDARD INSTALLATION 1) Operator 2) Mechanical stop 3) Electronic control unit EXIT 4) Flashing lamp 5) Right Photocell (Dx) 6) Differential switch 16A - 0,03A 7) Left Photocell (Sx) 8) Start/Stop push button with key 9) Antenna ENTRY 10) Support for photocells 11) Warning notice Fig. - Page 11 SURF INSTALLATION TYPE INWARD INSTALLATION OUTWARD INSTALLATION outside outside IN ANY CASE, I N S TA L L T H E O P E R A T O R ALWAYS INSIDE THE PROPERTY inside inside Fig. 11 Fig. 12 INWARD INSTALLATION Total stroke 15,75 in - max.
- Page 12 SURF K INSTALLATION TYPE INWARD INSTALLATION OUTWARD INSTALLATION outside outside IN ANY CASE, I N S TA L L T H E O P E R A T O R ALWAYS INSIDE THE PROPERTY inside inside Fig. 15 Fig. 16 INWARD INSTALLATION Opening Max Stroke...
- Page 13 INSTALLATION ON MASONRY PILLARS BY MAKING A RECESS 2,36 CAUTION! 7,87 During installation, make sure that the connection 42,05 6,10 Minimum cables do not interfere 3,14 Minimum with the recess NOTES 1 - dimensions in inches In case you need to make a recess, observe the shown dimensions 2,36...
- Page 14 PRELIMINARY NOTES 1 - For the correct operation it is very important to position both the operator and its front and rear fixing brackets, in a perfectly horizontal way, by using a level, as shown in Fig. 21 - 22 2 - Before mounting operator on the rear and the front brackets, lubricate with water repellent grease 3 - The operator must be mounted with the release facing upwards (Fig.
- Page 15 PRELIMINARY NOTES 1 - According to the gate type (wood, iron, aluminium) the front bracket can be welded or screwed 2 - Before mounting the rear and the front fixing brackets, lubricate with water repellent grease 3 - The operator position must be perfectly horizontal (use a level as shown in Fig. 28 or 29) 4 - Make sure that the front fixing bracket DOES NOT TILT when it reaches the stop (Fig.
-
Page 16: Mechanical Stop
When positioning the front fixing bracket on the gate, always consider the offset in respect to the central axis of the operator (see Fig. 33) 2,40'’ 0,91'’ Fig. 33 INSTALLATION OF MECHANICAL STOP FOR SURF MECHANICAL STOP IN CLOSING Max = 2,55 in Fig. - Page 17 - Make connections only after installation is complete and when the power supply is OFF -The connections shown refer to operators installed as « »; INWARD OPENING » installations follow the procedure shown in the Fig. 49 below For « OUTWARD OPENING SURF 24V SURF BR 36V...
-
Page 18: Periodic Maintenance
TO THE ATTENTION OF THE TECHNICIAN AND THE END-USER METALLIC INTERNAL RELEASE SYSTEM 90° To release the operator proceed as follows: 1) Turn counter-clockwise the lock protection cover (Fig. 50) Insert the key and turn of about 90° clockwise (Fig. 51) Lock Turn the handle... -
Page 19: Spare Parts
THE MANUFACTURER CAN NOT BE DEEMED RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED BY IMPROPER USE OF THIS PRODUCT SEA reserves the right to make all the necessary changes and modifications of the products or manuals without giving prior notice... - Page 20 SEA USA Inc. 10850 N.W. 21st - unit 160 - DORAL - MIAMI Florida (FL) 33172 Phone: ++1-305.594.1151 Toll Free: 800.689.4716 www.sea-usa.com sales@sea-usa.com...
Need help?
Do you have a question about the SURF 350 and is the answer not in the manual?
Questions and answers